1450059 VALVE GP-PILOT Caterpillar parts
IT24F, IT28F
Rating:
Alternative (cross code) number:
CA1450059
145-0059
1450059
CA1450059
145-0059
1450059
Weight: 20 pounds 9 kg.
INTEGRATED TOOLCARRIER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
1260002 Fs Curtis Air/Oil Separator - Same as: 1450059 - Made in USA
MASIA COMPRESSORS Made in USA || Meets or Exceeds OEM Requirements || Lifetime: 4000 Hours || Warranty: 6 months
MASIA COMPRESSORS Made in USA || Meets or Exceeds OEM Requirements || Lifetime: 4000 Hours || Warranty: 6 months
1450059 Air/Oil Separator Compatible with Fs Curtis
XSTORE Helps remove contaminants (metal fines, sludge, debris) to protect the lubrication circuit and bearings. || Extended Service Life – Engineered to provide reliable operation and longer intervals between filter changes. || Helps reduce unplanned maintenance and supports extended oil change intervals. || Durable Construction – Built with high-quality materials for consistent performance in demanding industrial environments. || Designed for Air Compressors – Suitable for use with rotary screw compressors and compatible with common industry standards.
XSTORE Helps remove contaminants (metal fines, sludge, debris) to protect the lubrication circuit and bearings. || Extended Service Life – Engineered to provide reliable operation and longer intervals between filter changes. || Helps reduce unplanned maintenance and supports extended oil change intervals. || Durable Construction – Built with high-quality materials for consistent performance in demanding industrial environments. || Designed for Air Compressors – Suitable for use with rotary screw compressors and compatible with common industry standards.
Number on catalog scheme:
7
For full view, you need register
Information:
Thickness Control Screws
The thickness control screws are used to introduce the angle of attack into the screed. There is one thickness control screw located on each end of the screed. The adjustment of the thickness control screws and the start up procedure are discussed in the "Setup Section" of this manual.Extender Controls
Height Adjuster
The height adjuster moves the screed extender up or down to keep the screed plate level with the main screed trailing edge when the attack angle is adjusted.There is a power option available. See your Caterpillar dealer.Sloper Control
1. The extenders adjust down from 0 to 8°.2. Turn the sloper crank clockwise, (as you view it), to put in the slope. The extender then pivots down.3. The extenders can be adjusted while paving. This does not change the main screed width.A power option is available for sloping the extenders. See you Caterpillar dealer.Extender Width Switch
The extender width switch moves the extender in and out as desired to achieve the overall desired paving width. The right extender is controlled by the extender width switch in the right screed control box. The left extender is controlled by the extender width switch in the left screed control box. Additional switches may be located on the tractor. See the tractor Operation Manual.Crown Control
No leading edge crown is required for the Extend-A-Mat screed.The crown control adjusts the screed to produce the desired contour of the finished pavement. Turn the control handle clockwise to increase crown to the desired setting. Make sure the crown control lock is engaged so the setting does not change while paving.A power option is also available for the crown control. See your Caterpillar dealer.Feeder Gain
The function of this system is to maintain a constant head of material in the feeder screw chamber by changing the speed of the feeder and the screw in proportion to the direction of the position of the sensor paddle. The feeder control system consists of the following:* Feeder Control Pots - The feeder control pots, with sensor paddles, are located on mounting shafts near the left and right hand outboard feeder screws.* Actuators - The actuators are located on each right and left hand feeder hydrostatic pump.* Auto-Manual Switch - The AUTO/MANUAL switches are located on the left and right operators station and the right and left Endgate boxes. The feeder control pot varies the voltage to the actuator valve that moves the swash plate of the feeder pump to speed up or slow down the feeder and screw as required. The feeder and screw are driven at maximum speed when the feeder control paddle arm is in the vertical position. As the asphalt in the screw chamber raises the paddle arm up to 45°, the voltage to the EDC decreases, moving the actuator toward neutral, until zero voltage is reached and the feeder screw stops. During operation, the paddle will be lifted to the position where material height will be maintained.Extended Feeder Control Mount
Adjustment of the feeder gate may be necessary when
The thickness control screws are used to introduce the angle of attack into the screed. There is one thickness control screw located on each end of the screed. The adjustment of the thickness control screws and the start up procedure are discussed in the "Setup Section" of this manual.Extender Controls
Height Adjuster
The height adjuster moves the screed extender up or down to keep the screed plate level with the main screed trailing edge when the attack angle is adjusted.There is a power option available. See your Caterpillar dealer.Sloper Control
1. The extenders adjust down from 0 to 8°.2. Turn the sloper crank clockwise, (as you view it), to put in the slope. The extender then pivots down.3. The extenders can be adjusted while paving. This does not change the main screed width.A power option is available for sloping the extenders. See you Caterpillar dealer.Extender Width Switch
The extender width switch moves the extender in and out as desired to achieve the overall desired paving width. The right extender is controlled by the extender width switch in the right screed control box. The left extender is controlled by the extender width switch in the left screed control box. Additional switches may be located on the tractor. See the tractor Operation Manual.Crown Control
No leading edge crown is required for the Extend-A-Mat screed.The crown control adjusts the screed to produce the desired contour of the finished pavement. Turn the control handle clockwise to increase crown to the desired setting. Make sure the crown control lock is engaged so the setting does not change while paving.A power option is also available for the crown control. See your Caterpillar dealer.Feeder Gain
The function of this system is to maintain a constant head of material in the feeder screw chamber by changing the speed of the feeder and the screw in proportion to the direction of the position of the sensor paddle. The feeder control system consists of the following:* Feeder Control Pots - The feeder control pots, with sensor paddles, are located on mounting shafts near the left and right hand outboard feeder screws.* Actuators - The actuators are located on each right and left hand feeder hydrostatic pump.* Auto-Manual Switch - The AUTO/MANUAL switches are located on the left and right operators station and the right and left Endgate boxes. The feeder control pot varies the voltage to the actuator valve that moves the swash plate of the feeder pump to speed up or slow down the feeder and screw as required. The feeder and screw are driven at maximum speed when the feeder control paddle arm is in the vertical position. As the asphalt in the screw chamber raises the paddle arm up to 45°, the voltage to the EDC decreases, moving the actuator toward neutral, until zero voltage is reached and the feeder screw stops. During operation, the paddle will be lifted to the position where material height will be maintained.Extended Feeder Control Mount
Adjustment of the feeder gate may be necessary when
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
1057707
VALVE & MTG GP-MAIN CONTROL
938F, IT38F
938F, IT38F
9T7420
VALVE GP-STEERING
938F, 938G, 938G II, IT38F, IT38G, IT38G II
938F, 938G, 938G II, IT38F, IT38G, IT38G II
1079530
VALVE GP-PUMP CONTROL
938F, 938G, 938G II, IT38F, IT38G, IT38G II
938F, 938G, 938G II, IT38F, IT38G, IT38G II
1124801
VALVE GP-BRAKE CONTROL
515, 525, 938F, IT38F
515, 525, 938F, IT38F
2120924
VALVE MECHANISM GP
914G, IT14G
914G, IT14G
1860905
VALVE GP-RELIEF
928G, 928HZ, IT24F, IT28G
928G, 928HZ, IT24F, IT28G
1189089
VALVE GP-CONTROL
IT24F
IT24F
1189088
VALVE GP-CONTROL
IT24F
IT24F
1257922
VALVE GP-RELIEF
IT24F
IT24F
1194122
VALVE GP-RELIEF
IT24F
IT24F