1975006 VALVE GP-CONTROL Caterpillar parts
M325B
Rating:
Alternative (cross code) number:
CA1975006
197-5006
1975006
CA1975006
197-5006
1975006
WHEELED EXCAVATOR,
Compatible equipment models: 1975006:
Number on catalog scheme:
12
For full view, you need register
Information:
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
The engine can start automatically. Ensure that the power supply is isolated before any service or repairs is performed.
Illustration 1 g01340605
Typical example
If necessary, remove the assembly of dipstick tube. Loosen nut (1) and remove tube assembly (2). remove seal (3) from the tube assembly. Note: Identify the position and orientation of the tube assembly.
Illustration 2 g01616335
Drain the engine lubricating oil from the engine oil pan into a suitable container. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
Disconnect the breather hose from the closed circuit breather valve on the engine oil pan. Position the breather hose away from the engine oil pan.
Illustration 3 g01543236
Engines that are keel cooled and sea water cooled remove bolts (8) from engine mount (9). Sufficiently loosen nuts and bolts (8) on the engine with a radiator cooling system. Engines with a radiator cooled systems. Sufficiently loosen both the generator mounting bolts.
Use a suitable lifting device to lift the front of the engine. The weight of the engine is approximately 600 kg (1323 lb). Raise the front of the engine so that there is a distance of 12 mm (0.50 inch) between mount (9) and the base frame. Support the weight of the engine with suitable cribbing under mount (9).
Support engine oil pan (5). Loosen bolts (6) and bolts (7). There are 30 bolts in total Note: Bolts (6) and (7) are held captive by gasket (4).
Remove engine oil pan (5) from the engine. Installation Procedure
Illustration 4 g01616335
Ensure that engine oil pan (5) is clean and free from damage. Clean bolts (6) and (7). Inspect the bolts for deterioration or damage. If necessary, replace the bolts . Ensure that the gasket surface of the engine oil pan plate is clean. Note: The bolts must be replaced as a complete set to ensure even clamping of the engine oil pan.
Position a new gasket (4) onto the engine oil pan (5).
Illustration 5 g01340724
(Z) Position of the short engine oil pan bolts.
Install bolts (5) and (6) to the engine oil pan. Do not install the bolts to the large holes at Positions (X) in the engine oil pan. Note: Bolts (5) and (6) are held captive by the gasket.
Install engine oil pan (5) and the gasket to the engine oil pan plate. Tighten the engine oil pan bolts to a torque of 22 N m (195 lb in) in the sequence that is shown in Illustration 5. There are 26 bolts in total.
Illustration 6 g01340725
Install the four remaining engine oil pan bolts and
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
320, 320 L, 320N, 322, 322 FM L, 322 LN, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, M325B
318C, 319C, 320C, 320C FM, 321C, 322B L, 322C, 322C FM, 325B L, 325C, 325C FM, 325D, 330B L, 330C, 330C FM, 330C L, 330C MH, M325B, M325C MH, TK1051, W330B
307B, 307C, 308C, 311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E...
307D, 308D, 311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315B, ...
312C L, 318C, 319C, 320B, 320B FM LL, 320B L, 320B U, 320C, 320C FM, 321B, 321C, 322B, 322B L, 322B LN, 322C, 322C FM, 325B, 325B L, 325C, 325C FM, 325C L, 325D, 330B, 330B L, 330C, 330C FM, 330C L, 3...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 325B, 325B L, 325C, 325C FM, 325D, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330, 330B, 330B L, 330D FM, 345C, 345C ...
320, 320 L, 320N, 322, 322 FM L, 322 LN, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, M325B
325B, 325B L, 330B, 330B L, 539, M325B, W330B
120H, 120H ES, 120H NA, 135H, 135H NA, 30/30, 3114, 3116, 3126, 320B, 322 FM L, 322B L, 322B LN, 322C, 322C FM, 325B L, 35, 446B, 446D, 45, 525B, 533, 535B, 539, 543, 55, 550, 561M, 570, 574, 580, 613...
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 140M, 140M 2, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 160M, 160M 2, 163H NA, 1673C, 215, 225, 235, 235B, 3116, 3176, ...
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140B, 140G, 140H, 140H ES, 1...
305.5, 306, 306E, 307B, 307C, 307D, 308C, 308D, 311, 311B, 311C, 311D LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 313B, 314C, 314D CR, 314D LCR, 315, 315B, 315B L, 315C, 315D L, 317B LN, 318B, 318C...
1376706
VALVE GP-CHECK & RELIEF
325B L, M325B
325B L, M325B
1376707
VALVE GP-CHECK & RELIEF
325B L, M325B
325B L, M325B
1058909
VALVE GP-BANK 6
428C, 438C
428C, 438C
3371880
VALVE GP-TRANSMISSION CONTROL
980H, 980K, 980K HLG, 986H
980H, 980K, 980K HLG, 986H
1515184
VALVE & LINES GP-PRIORITY
M312, M315
M312, M315
2899640
VALVE GP-SEQUENCE
844K, 854K, 990K, 992K
844K, 854K, 990K, 992K
3422154
VALVE & LINKAGE GP
12K, 140K, 140K 2, 160K
12K, 140K, 140K 2, 160K
1135622
VALVE GP
45, 55
45, 55
3807931
VALVE MECHANISM GP
320D GC, 320D L, 323D L
320D GC, 320D L, 323D L