2054723 VALVE Caterpillar parts
3013, 3014, 302.5, 3024, 303.5, 902, CB-214D, CB-334D, CB-335D
Rating:
Alternative (cross code) number:
CA2054723
205-4723
2054723
CA2054723
205-4723
2054723
Weight: 0.02 pounds 0 kg.
COMPACT WHEEL LOADER, VIBRATORY COMPACTOR,
Compatible equipment models: 2054723:
Number on catalog scheme:
4
For full view, you need register
Information:
Probable Causes
Engine oil cooler
Cylinder head gasket
Cylinder head
Cylinder blockRecommended Actions
Complete the procedure in the order in which the steps are listed.
Table 1
Troubleshooting Test Steps Values Results
1. Engine Oil Cooler
A. Drain the coolant from the cooling system. Drain the lubricating oil from the engine oil cooler. Refer to the Operation and Maintenance Manual for more information.
B. Check for leaks in the engine oil cooler. Refer to Systems Operation, Testing, and Adjusting, "Cooling System" for the correct procedure.
Oil Cooler
Result: A leak is found in the engine oil cooler.
Repair: Install a new oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove" and Disassembly and Assembly, "Engine Oil Cooler - Install" for the correct procedure.
Flush the cooling system. Refer to the Operation and Maintenance Manual for the correct procedure. Refill the cooling system with the correct coolant. Refer to the Operation and Maintenance Manual for the recommended coolant and capacities.
After the leak has been repaired, refill the engine with oil of the correct specification . Refer to the Operation and Maintenance Manual for the correct oil capacity and viscosity.
Result: A leak was not found in the engine oil cooler.
Proceed to Test Step 2.
2. Cylinder Head Gasket
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
B. Inspect the cylinder head gasket for faults and any signs of leakage.
Cylinder head gasket
Result: The cylinder head gasket does not show signs of damage or leakage.
Repair: Install a new cylinder head gasket and install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" .
Result: The cylinder head gasket shows signs of damage or leakage.
Proceed to Test Step 3.
3. Cylinder Head
A. Check for cracks in the cylinder head. Perform a leak test on the cylinder head. Refer to System Operation, Testing and Adjusting, "Cylinder Head - Inspect" for the correct procedure.
Cylinder head
Result: A fault was found in the cylinder head.
Repair: Repair the cylinder head or replace the cylinder head. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Result: A fault was not found in the cylinder head.
Proceed to Test Step 4.
4. Cylinder Block
A. Inspect the top face of the cylinder block for faults and signs of leakage.
Refer to Systems Operation, Testing, and Adjusting, "Cylinder Block - Inspect" for the correct procedure.
Cylinder block
Result: A fault was found in the cylinder block.
Repair: Repair the cylinder block or replace the cylinder block. Inspect the top deck. Refer to the Reuse and Salvage Guidelines for the correct inspection procedure.
Result: No fault was found in the cylinder block.
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Contact the Dealer Solutions Network (DSN).
Engine oil cooler
Cylinder head gasket
Cylinder head
Cylinder blockRecommended Actions
Complete the procedure in the order in which the steps are listed.
Table 1
Troubleshooting Test Steps Values Results
1. Engine Oil Cooler
A. Drain the coolant from the cooling system. Drain the lubricating oil from the engine oil cooler. Refer to the Operation and Maintenance Manual for more information.
B. Check for leaks in the engine oil cooler. Refer to Systems Operation, Testing, and Adjusting, "Cooling System" for the correct procedure.
Oil Cooler
Result: A leak is found in the engine oil cooler.
Repair: Install a new oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove" and Disassembly and Assembly, "Engine Oil Cooler - Install" for the correct procedure.
Flush the cooling system. Refer to the Operation and Maintenance Manual for the correct procedure. Refill the cooling system with the correct coolant. Refer to the Operation and Maintenance Manual for the recommended coolant and capacities.
After the leak has been repaired, refill the engine with oil of the correct specification . Refer to the Operation and Maintenance Manual for the correct oil capacity and viscosity.
Result: A leak was not found in the engine oil cooler.
Proceed to Test Step 2.
2. Cylinder Head Gasket
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
B. Inspect the cylinder head gasket for faults and any signs of leakage.
Cylinder head gasket
Result: The cylinder head gasket does not show signs of damage or leakage.
Repair: Install a new cylinder head gasket and install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" .
Result: The cylinder head gasket shows signs of damage or leakage.
Proceed to Test Step 3.
3. Cylinder Head
A. Check for cracks in the cylinder head. Perform a leak test on the cylinder head. Refer to System Operation, Testing and Adjusting, "Cylinder Head - Inspect" for the correct procedure.
Cylinder head
Result: A fault was found in the cylinder head.
Repair: Repair the cylinder head or replace the cylinder head. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Result: A fault was not found in the cylinder head.
Proceed to Test Step 4.
4. Cylinder Block
A. Inspect the top face of the cylinder block for faults and signs of leakage.
Refer to Systems Operation, Testing, and Adjusting, "Cylinder Block - Inspect" for the correct procedure.
Cylinder block
Result: A fault was found in the cylinder block.
Repair: Repair the cylinder block or replace the cylinder block. Inspect the top deck. Refer to the Reuse and Salvage Guidelines for the correct inspection procedure.
Result: No fault was found in the cylinder block.
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Contact the Dealer Solutions Network (DSN).
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140B, 140G, 140H, 140H ES, 1...
1090, 1190, 1190T, 120, 120B, 120G, 120H, 120H ES, 120H NA, 1290T, 12F, 12G, 12H, 12H NA, 130G, 135H, 135H NA, 1390, 140, 140B, 140G, 140H, 140H NA, 143H, 14E, 14H, 16, 160H, 163H, 16G, 16H NA, 16M, 2...
3114, 3116, 3126B, 3176, 3176B, 3176C, 3196, 3406B, 3412E, 35, 3512, 45, 55, 613C, 613C II, 613G, 69D, 936, 936F, 980F, 980G, AD30, AD40, AD45, AD55, AE40, AE40 II, AP-1000B, AP-1055B, AP-1055D, AP-90...
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3013C, 3024, 3024C, 304.5, 902, AP-255E, BB-621C, C1.1, C1.5, C2.2, CB-214E, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CB34B, CB34B XW, ...
216, 216B, 216B3, 226B, 232B, 242B, 247B, 257B, 3013C, 3024, 3024C, 304.5, 902, AP-255E, BB-621C, C1.1, C1.5, C2.2, CB-214E, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B
216B, 232B, 242B, 3024C, 303.5, C1.5
3013, 302.5, CB-214D, CB-334D, CB-335D
3013, 302.5, CB-214D, CB-334D, CB-335D
301.5, 302.5C, 303, 303.5, 303E CR, 304.5, 305, 305.5, 305.5E, 306, 306E
2071253
VALVE
3024, 304.5
3024, 304.5
1415288
VALVE
SCT673, SPF343, SPF343C, SPS343, SPT342, SPT343
SCT673, SPF343, SPF343C, SPS343, SPT342, SPT343
1455442
VALVE
SPF343, SPF343C, SPT342
SPF343, SPF343C, SPT342
1455441
VALVE-RELIEF
SPF343C, SPT342
SPF343C, SPT342
CPT372, SCT673, SPF343, SPF343C, SPS342, SPS343, SPT342, SPT343
1804794
VALVE-RELIEF
CPT372, SCT673, SPF343, SPF343C, SPS342, SPS343, SPT342, SPT343
CPT372, SCT673, SPF343, SPF343C, SPS342, SPS343, SPT342, SPT343
3013, 302.5, CB-214D, CB-334D, CB-335D
3013, 302.5, CB-214D, CB-334D, CB-335D
2055863
VALVE
3003, 301.5
3003, 301.5
1535560
VALVE-INLET
3003, 301.5
3003, 301.5
3003, 301.5, 3011C, 3013C, C1.1, C1.6, CB-14
1536852
VALVE-RELIEF
3003, 3014
3003, 3014