2107775 VALVE GP-BANK 4 Caterpillar parts
D8T
Rating:
Alternative (cross code) number:
CA2107775
210-7775
2107775
CA2107775
210-7775
2107775
Weight: 264 pounds 119 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 2107775:
Number on catalog scheme:
8
For full view, you need register
Information:
ALIGN="center">Tube
1 8S-8048 Saddle
1 8S-7615 Pin
Install protective strips (14) between the main rotor and the main stator. The protective strips are used in order to protect both the rotor and the stator. Refer to the two "Notice" paragraphs that are at the beginning of the "Rotor - Remove and Install" section for more information about the protective strips that must be used.
Illustration 10 g01632115
Assemble the 138-7576 Link Brackets (15) and the 3E-3881 Eyebolt (16) onto the main rotor (17) front hub.
Illustration 11 g01463732
Place the rotor removal tool (21) onto the main rotor (22). Install the rotor removal tool onto the rotor until the tool rests against the step face (23) that is on the rotor shaft. Install the suitable lifting device (24) to the rotor assembly.
Illustration 12 g01463735
Support rotor removal tool (28) with the tool stand assembly (29).
Illustration 13 g01463867
Attach one end of the ratchet hoist (31) to the eye bolt (32 ). Attach the opposite end (30) of the ratchet hoist (31) to a suitable object. Note: The ratchet hoist allows a slow controlled removal of the rotor assembly.Note: The main rotor position must remain as horizontal as possible during removal in order to avoid any damage to the generator components.
Illustration 14 g01463887
Attach a suitable lifting device (33) to the link brackets (34). The weight of the rotor assembly varies depending on the generator size. The rotor weight can be from 845 kg (1863 lb) to 1236 kg (2725 lb).
Use the ratchet hoist (40) and the rotor removal tool in order to finish the removal of the main rotor (41) from the stator (42).
Illustration 15 g014664881400, 1600, and 1800 Frame Main Rotor Installation Procedure
The information that is in the following procedure is applicable for both single bearing and double bearing generators, except for the minor difference where noted.
Place a protective strip (43) of plastic or curved sheet metal between the rotor assembly and the stator assembly. Note: The protective strip should be as long as the rotor assembly. During installation of the rotor, the protective strip will protect the rotor and the stator from damage.
Illustration 16 g01301189
(43) Protective strip
On two bearing generators rotors, orient the alignment mark that is on the front bearing bracket to the mark that is on the stator.
Illustration 17 g01301247
Attach a suitable lifting device to rotor assembly. Assemble the rotor removal tooling to the rearward end of the rotor shaft.
Install the rotor into the stator as far as possible, as shown in Illustration 18. Remove the strap (44).
Illustration 18 g01301257
Use the rotor removal tool in order to guide the rotor assembly and fan assembly to the stator housing.
On two bearing generators, install the mounting bolts (48) that are used in order to secure the front bearing bracket (49) to the stator (50). Torque the mounting bolts (48).
Illustration 19 g01632296
Install the end bracket if it was removed.
Install the end bracket if it was removed.
Remove the protective strips (51).
Illustration 20 g01632303
Remove the tooling that was used in order to install the rotor.
Install the exciter bearing retainer bar (4). Torque the bolts. Refer
1 8S-8048 Saddle
1 8S-7615 Pin
Install protective strips (14) between the main rotor and the main stator. The protective strips are used in order to protect both the rotor and the stator. Refer to the two "Notice" paragraphs that are at the beginning of the "Rotor - Remove and Install" section for more information about the protective strips that must be used.
Illustration 10 g01632115
Assemble the 138-7576 Link Brackets (15) and the 3E-3881 Eyebolt (16) onto the main rotor (17) front hub.
Illustration 11 g01463732
Place the rotor removal tool (21) onto the main rotor (22). Install the rotor removal tool onto the rotor until the tool rests against the step face (23) that is on the rotor shaft. Install the suitable lifting device (24) to the rotor assembly.
Illustration 12 g01463735
Support rotor removal tool (28) with the tool stand assembly (29).
Illustration 13 g01463867
Attach one end of the ratchet hoist (31) to the eye bolt (32 ). Attach the opposite end (30) of the ratchet hoist (31) to a suitable object. Note: The ratchet hoist allows a slow controlled removal of the rotor assembly.Note: The main rotor position must remain as horizontal as possible during removal in order to avoid any damage to the generator components.
Illustration 14 g01463887
Attach a suitable lifting device (33) to the link brackets (34). The weight of the rotor assembly varies depending on the generator size. The rotor weight can be from 845 kg (1863 lb) to 1236 kg (2725 lb).
Use the ratchet hoist (40) and the rotor removal tool in order to finish the removal of the main rotor (41) from the stator (42).
Illustration 15 g014664881400, 1600, and 1800 Frame Main Rotor Installation Procedure
The information that is in the following procedure is applicable for both single bearing and double bearing generators, except for the minor difference where noted.
Place a protective strip (43) of plastic or curved sheet metal between the rotor assembly and the stator assembly. Note: The protective strip should be as long as the rotor assembly. During installation of the rotor, the protective strip will protect the rotor and the stator from damage.
Illustration 16 g01301189
(43) Protective strip
On two bearing generators rotors, orient the alignment mark that is on the front bearing bracket to the mark that is on the stator.
Illustration 17 g01301247
Attach a suitable lifting device to rotor assembly. Assemble the rotor removal tooling to the rearward end of the rotor shaft.
Install the rotor into the stator as far as possible, as shown in Illustration 18. Remove the strap (44).
Illustration 18 g01301257
Use the rotor removal tool in order to guide the rotor assembly and fan assembly to the stator housing.
On two bearing generators, install the mounting bolts (48) that are used in order to secure the front bearing bracket (49) to the stator (50). Torque the mounting bolts (48).
Illustration 19 g01632296
Install the end bracket if it was removed.
Install the end bracket if it was removed.
Remove the protective strips (51).
Illustration 20 g01632303
Remove the tooling that was used in order to install the rotor.
Install the exciter bearing retainer bar (4). Torque the bolts. Refer
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140G, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 16M, 2290...
446D, 621H, 621K, 623K, 623K LRC, 627H, 627K, 627K LRC, 793F CMD, 834K, 836K, 928HZ, 930G, 938H, 950H, 950K, 962H, 962K, 963D, 966H, 966K, 966M, 966M XE, 972H, 972K, 972M, 972M XE, 973D, 980K, 980K HL...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 24H, 24M, 525B, 525C, 535B, 535C, 545, 545C, 561N, 572R, 572R II, 583T, 587T, ...
D5R LGP, D6N, D6N LGP, D6N OEM, D6R II, D6R III, D6T, D6T LGP, D6T XL, D7R II, D8R II, D8T, D9T
561N, 572R, 572R II, 583T, 587T, D10T, D11T, D5M, D5N, D5R LGP, D6M, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL, D7E, D7E LGP, D7R II, D8R II, D8T, D9T, PL83, PL87
561N, 572R, 572R II, 583T, D10R, D5M, D5N, D6M, D6N, D6R, D6R II, D7R, D7R II, D8R II, D8T, D9T
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140B, 140G, 140H, 140H ES, 1...
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120M, 1290T, 12G, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 1390, 140G, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 16...
1090, 1190, 1190T, 120, 120B, 120G, 120H, 120H ES, 120H NA, 1290T, 12F, 12G, 12H, 12H NA, 130G, 135H, 135H NA, 1390, 140, 140B, 140G, 140H, 140H NA, 143H, 14E, 14H, 16, 160H, 163H, 16G, 16H NA, 16M, 2...
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 385B, 385C, 385C FS, 385C L, 385C L MH, 5090B, 583T, 587T, 621G, 623G, 627F, 627G, 631D, 631G, 637G, 651B, 657B, 657E, 657G, 735, 740, 770, 772, 773F, 773G, ...
1090, 1190, 1190T, 120H, 120K, 120K 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 1390, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M 2, 160M 3, 160M 3 AWD, 16M, 236D, 242...
517, 527, 561M, 561N, 572R II, 583R, 583T, 587R, 587T, 589, 623G, 933C, 939C, 973D, D10R, D10T, D10T2, D11R, D11T, D3C III, D3G, D3K XL, D3K2 LGP, D4C III, D4G, D4K XL, D4K2 XL, D5C III, D5G, D5HTSK I...
1243325
VALVE GP-BANK 4
120H, 120K, 120K 2, 12H, 12K, 135H, 140H, 140K, 140K 2, 160H, 160K
120H, 120K, 120K 2, 12H, 12K, 135H, 140H, 140K, 140K 2, 160H, 160K
24H, 5110B, 5130, 5130B, 5230, 5230B, 651E, 69D, 773D, 773E, 775E, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC,...
7G1364
VALVE GP-TRANSMISSION CONTROL
768C, 769C, 769D, 771C, 771D
768C, 769C, 769D, 771C, 771D
1081874
VALVE MECHANISM GP
24H, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 775B, 775D, 775E, 844, 990, 990 II, 992C, C30, C32, D10N, D10R, D9L
24H, 3412E, 5110B, 651E, 657E, 773B, 773D, 773E, 775B, 775D, 775E, 844, 990, 990 II, 992C, C30, C32, D10N, D10R, D9L
9T1179
VALVE GP
D6H
D6H
CG137-08, CG137-12, G3408C, G3412, G3412C, G3508, G3512, G3516
1485608
VALVE & MTG GP-CONTROL
CS-531D, CS-533D, CS-563D, CS-573D, CS-583D, CS-663E, CS-683E
CS-531D, CS-533D, CS-563D, CS-573D, CS-583D, CS-663E, CS-683E
4372869
VALVE GP-CONTROL
262D, 272D XHP, 277D, 279D, 299D, 299D XHP
262D, 272D XHP, 277D, 279D, 299D, 299D XHP
311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 315D L, 318D L, 318D2 L, 319D L, 319D LN, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D...
6E6031
VALVE GP-CONTROL
D6H, D6H II, D6H XL, D6H XR
D6H, D6H II, D6H XL, D6H XR
6E3034
VALVE GP-CONTROL
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H
120H, 120H ES, 120H NA, 135H, 135H NA, 3116, 320B, 322B, 322B L, 322B LN, 322C, 322C FM, 325B, 325B L, 35, 45, 525B, 533, 535B, 539, 543, 55, 550, 561M, 570, 574, 580, 613C II, 938F, 938G, 950G, 953C,...