2316959 VALVE GP-CONTROL Caterpillar parts
320C, 330C, 330C L
Rating:
Alternative (cross code) number:
CA2316959
231-6959
2316959
CA2316959
231-6959
2316959
Weight: 242 pounds 109 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
Compatible equipment models: 2316959:
Number on catalog scheme:
2
For full view, you need register
Information:
Removal Procedure
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Use the following procedure to release the pressure in the hydraulic system:
Lower the implements to the ground.
Shut off the engine.
Move the control levers through the full travel distance of the levers. This will relieve any pressure in the pilot system.
Slowly loosen the filler cap on the hydraulic oil tank in order to release the pressure.
Tighten the filler cap on the hydraulic oil tank.
The pressure in the hydraulic system has now been relieved. Lines and components can now be removed.Note: Put identification on all lines, hoses, wires, and tubes for installation purposes. Install a cap or plug on all lines, hoses, and tubes that are disconnected. The caps and/or plugs prevent the loss of fluid and contaminants cannot enter the system.
Illustration 1 g00636249
Remove cover (1) from grapple (2) .
Illustration 2 g00636250
Disconnect hose assemblies (3) and (4) .
Illustration 3 g00636252
Use a lift truck to support the grapple head.
Remove the bolt and retainer (6) .
Remove nut (5) and the pin.
Remove friction disc and bushings (7). Separate the grapple head from crossblock (8). The approximate weight of the grapple head is 743 kg (1638 lb).Installation Procedure
Illustration 4 g00636252
The approximate weight of the grapple head is 743 kg (1638 lb). Use a lift truck to place the grapple head in position in the crossblock for installation. Install friction disc and bushings (7) .
Install the pin and nut (5) .
Install retainer (6) and the bolt.
Check the oil level in the hydraulic tank.Note: Refer to the Operation and Maintenance Manual, SEBU7001, "Hydraulic System Oil Level - Check" for the correct procedure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Use the following procedure to release the pressure in the hydraulic system:
Lower the implements to the ground.
Shut off the engine.
Move the control levers through the full travel distance of the levers. This will relieve any pressure in the pilot system.
Slowly loosen the filler cap on the hydraulic oil tank in order to release the pressure.
Tighten the filler cap on the hydraulic oil tank.
The pressure in the hydraulic system has now been relieved. Lines and components can now be removed.Note: Put identification on all lines, hoses, wires, and tubes for installation purposes. Install a cap or plug on all lines, hoses, and tubes that are disconnected. The caps and/or plugs prevent the loss of fluid and contaminants cannot enter the system.
Illustration 1 g00636249
Remove cover (1) from grapple (2) .
Illustration 2 g00636250
Disconnect hose assemblies (3) and (4) .
Illustration 3 g00636252
Use a lift truck to support the grapple head.
Remove the bolt and retainer (6) .
Remove nut (5) and the pin.
Remove friction disc and bushings (7). Separate the grapple head from crossblock (8). The approximate weight of the grapple head is 743 kg (1638 lb).Installation Procedure
Illustration 4 g00636252
The approximate weight of the grapple head is 743 kg (1638 lb). Use a lift truck to place the grapple head in position in the crossblock for installation. Install friction disc and bushings (7) .
Install the pin and nut (5) .
Install retainer (6) and the bolt.
Check the oil level in the hydraulic tank.Note: Refer to the Operation and Maintenance Manual, SEBU7001, "Hydraulic System Oil Level - Check" for the correct procedure.
Caterpillar SIS machinery equipment:
Caterpillar SIS
330C L & 330C LN Excavators CAP00001-UP (MACHINE) POWERED BY C-9 Engine »
231-6959
VALVE GP-CONTROL
320C S Hydraulic Excavator EGL00001-UP (MACHINE) POWERED BY 3066 Engine »
231-6959
VALVE GP-CONTROL
330C & 330C L Excavators JAB00001-UP (MACHINE) POWERED BY C-9 Engine »
231-6959
VALVE GP-CONTROL
330C L Material Handler MKM00001-UP (MACHINE) POWERED BY C-9 Engine »
231-6959
VALVE GP-CONTROL
330C & 330C L Excavators JCD00001-UP (MACHINE) POWERED BY C-9 Engine »
231-6959
VALVE GP-CONTROL
330C Mobile Hydraulic Power Unit MSL00001-UP (MACHINE) POWERED BY C-9 Engine »
231-6959
VALVE GP-CONTROL
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
311B, 312B, 312C, 312C L, 315C, 318B, 318C, 319C, 320B, 320C, 320C FM, 320C L, 322C, 325B, 325C, 330C, 330C L, 345B II, 350, 365B, 365B L, 375, 385B
1290T, 1390, 2491, 2590, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D...
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321B, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM RR, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 3...
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B U, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN, E110, E110B, E120B, E200B, E450
312C, 312C L, 315C, 318C, 319C, 320C, 320C FM, 320C L, 320D, 320D FM RR, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 322C, 323D L, 323D LN, 324D, 325C, 325D, 325D L, 330C, 330C L, 330D, 330D L
311C, 312C, 312C L, 314C, 318C, 319C, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
318C, 319C, 320, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, ...
1907704
VALVE GP-CONTROL
320C, 330C, 330C FM, 330C L
320C, 330C, 330C FM, 330C L
1907702
VALVE GP-CONTROL
320C, 330C, 330C FM, 330C L
320C, 330C, 330C FM, 330C L
1844629
VALVE GP-CONTROL
320B, 320C, 330C, 330C L
320B, 320C, 330C, 330C L
2303431
VALVE AR-STICK LOWERING CONT
330C, 330C L
330C, 330C L
1907804
VALVE AR-CHECK & RELIEF
330C, 330C L
330C, 330C L
1907770
VALVE GP-SOLENOID
325C, 330C L
325C, 330C L
2597756
VALVE GP-MAIN CONTROL
320C, 330C, 330C L
320C, 330C, 330C L
2695496
VALVE GP-LOAD CONTROL
325C, 330C, 330C L
325C, 330C, 330C L
2154408
VALVE GP-LOAD CONTROL
325C, 330C, 330C L
325C, 330C, 330C L
2580289
VALVE GP-CONTROL
320C, 330C, 330C L
320C, 330C, 330C L