2580291 VALVE GP-CONTROL Caterpillar parts
320C, 330C, 330C FM, 330C L
Rating:
Alternative (cross code) number:
CA2580291
258-0291
2580291
CA2580291
258-0291
2580291
Weight: 175 pounds 79 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
Compatible equipment models: 2580291:
Number on catalog scheme:
3
For full view, you need register
Information:
1. Put the fuel injection pump housing on tool (A). 2. Remove bolts (1) that hold the governor housing (2) to the fuel injection pump housing. 3. Remove governor housing (2) from pump housing. 4. Remove cover (5) over the torque spring.5. Remove spring (8), (wave) washer (7) and guide (6) from governor housing.6. Remove seat (3) and over fueling spring (4).7. Pull shaft (9) up and remove shaft and lever from the housing. 8. Remove torque spring assembly (10) and pin. Some fuel systems do not have a torque spring. They have only a stop.9. Remove riser (follower) (11) from the shaft.10. Remove ring and lever (12) from the dowel. 11. Remove cover (13) for the flyweights with tool (B). Tool (B) can cause damage to the cover. Always inspect cover and install a new cover if needed. 12. Install timing pin (14) to hold the camshaft from turning.13. Remove bolts (15) that hold flyweight assembly to camshaft. 14. Remove the flyweight assembly (16) from the fuel injection pump housing.15. Remove the timing pin from the housing.Connection Of Governor To Fuel Injection Pump Housing
1. Put the fuel injection pump housing on tool (A).2. Install timing pin (1) to keep the camshaft from turning.3. Put flyweight assembly (2) in position on the camshaft.
Be sure pin (3) that holds shaft is in the correct position on back of the flyweight assembly.
4. Install new bolts for the flyweight assembly. The bolts for the flyweight assembly have a locking material on the threads and must not be used more than one time. 5. Install cover over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (4). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover that is bent.
7. Install lever (5) on the dowel. Install ring (6) that holds lever on dowel. 8. Install pin (7) in the housing with the round end down. 9. Put riser (follower) (10) in position between the flyweights. Lift the flyweight up with a piece of wire and push riser (follower) forward.10. Put lever (9) into position in groove of riser (follower) (10) and ball end engaged in the sleeve shaft lever (8). Install shaft to hold lever in place.
If lever (9) is not installed correctly, the governor cannot operate and can cause the engine to over speed.
11. Install over fueling spring (13) and seat (12) on shaft.12. Install stud (14) and torque spring or stop bar (11) on the housing.
The screw that holds the torque spring must not go beyond the inner surface of the governor housing.
13. Install cover (15) over torque spring after adjustment has been made.14. Install guide, (wave) washer and spring (16) in the governor housing.15. Put the governor housing on the fuel injection pump housing and
1. Put the fuel injection pump housing on tool (A).2. Install timing pin (1) to keep the camshaft from turning.3. Put flyweight assembly (2) in position on the camshaft.
Be sure pin (3) that holds shaft is in the correct position on back of the flyweight assembly.
4. Install new bolts for the flyweight assembly. The bolts for the flyweight assembly have a locking material on the threads and must not be used more than one time. 5. Install cover over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (4). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover that is bent.
7. Install lever (5) on the dowel. Install ring (6) that holds lever on dowel. 8. Install pin (7) in the housing with the round end down. 9. Put riser (follower) (10) in position between the flyweights. Lift the flyweight up with a piece of wire and push riser (follower) forward.10. Put lever (9) into position in groove of riser (follower) (10) and ball end engaged in the sleeve shaft lever (8). Install shaft to hold lever in place.
If lever (9) is not installed correctly, the governor cannot operate and can cause the engine to over speed.
11. Install over fueling spring (13) and seat (12) on shaft.12. Install stud (14) and torque spring or stop bar (11) on the housing.
The screw that holds the torque spring must not go beyond the inner surface of the governor housing.
13. Install cover (15) over torque spring after adjustment has been made.14. Install guide, (wave) washer and spring (16) in the governor housing.15. Put the governor housing on the fuel injection pump housing and
Caterpillar SIS machinery equipment:
Caterpillar SIS
330C Excavator MSD00001-UP (MACHINE) POWERED BY C-9 Engine »
258-0291
VALVE GP-CONTROL
330C L & 330C LN Excavators CAP00001-UP (MACHINE) POWERED BY C-9 Engine »
258-0291
VALVE GP-CONTROL
330C & 330C L Excavators GKX00001-UP (MACHINE) POWERED BY C-9 Engine »
258-0291
VALVE GP-CONTROL
320C S Hydraulic Excavator EGL00001-UP (MACHINE) POWERED BY 3066 Engine »
258-0291
VALVE GP-CONTROL
330C & 330C L Excavators JAB00001-UP (MACHINE) POWERED BY C-9 Engine »
258-0291
VALVE GP-CONTROL
330C L Excavator DKY00001-UP (MACHINE) POWERED BY C-9 Engine »
258-0291
VALVE GP-CONTROL
330C Forest Swing Machines B4N00001-UP (MACHINE) POWERED BY C-9 Engine »
258-0291
VALVE GP-CONTROL
330C & 330C L Excavators JCD00001-UP (MACHINE) POWERED BY C-9 Engine »
258-0291
VALVE GP-CONTROL
330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine »
258-0291
VALVE GP-CONTROL
330C Mobile Hydraulic Power Unit MSL00001-UP (MACHINE) POWERED BY C-9 Engine »
258-0291
VALVE GP-CONTROL
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
311B, 312B, 312C, 312C L, 315C, 318B, 318C, 319C, 320B, 320C, 320C FM, 320C L, 322C, 325B, 325C, 330C, 330C L, 345B II, 350, 365B, 365B L, 375, 385B
1290T, 1390, 2491, 2590, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D...
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321B, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM RR, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 3...
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B U, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN, E110, E110B, E120B, E200B, E450
312C, 312C L, 315C, 318C, 319C, 320C, 320C FM, 320C L, 320D, 320D FM RR, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 322C, 323D L, 323D LN, 324D, 325C, 325D, 325D L, 330C, 330C L, 330D, 330D L
311C, 312C, 312C L, 314C, 318C, 319C, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
318C, 319C, 320, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, ...
C-9, C13, C15, C7, C9, TH31-E61, TH35-C13T, TH35-C15T
1425522
VALVE GP-CONTROL
330B, 330B L
330B, 330B L
3489819
VALVE GP-CONTROL
450E, 450F
450E, 450F
C13, C15, C7, C9, TH31-E61, TH35-C13T, TH35-C15T
6E5653
VALVE GP-MAKEUP
517, 527, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D6M
517, 527, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D6M
1991153
VALVE GP-SOLENOID
M313C, M313D, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH, M325C MH, M325D L MH, M325D MH, M330D
M313C, M313D, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH, M325C MH, M325D L MH, M325D MH, M330D
2851362
VALVE GP-CONTROL
330D, 330D L, 330D LN, 336D L, 336D LN
330D, 330D L, 330D LN, 336D L, 336D LN
768C, 769C, 772B, 773B, 776, 777, 777B
1077015
VALVE GP-CONTROL
330B, 330B L, W330B
330B, 330B L, W330B
1077010
VALVE GP-MAIN CONTROL
330B, 330B L, W330B
330B, 330B L, W330B
2448402
VALVE GP-CONTROL
318C, 320C, 321C, 322C, 325C, 330C L
318C, 320C, 321C, 322C, 325C, 330C L