VALVE GP-SOLENOID 2625265 - Caterpillar

Engine:
3116 (S/N: 1NJ1-UP)
3208 (S/N: 30A1-UP)
3304 (S/N: 02B4226-UP; 04B4555-UP; 83Z1-UP)
3306 (S/N: 66D8891-UP)
3304B (S/N: DED1-UP; 9HK1-UP)
3306B (S/N: EFA1-UP; 8JJ1-UP; 9NR1-UP; 8NS1-UP; LRW1-UP)
3406 (S/N: 4JK1-98; 90U1-UP; 75Z1-UP)
3406C (S/N: 4JK99-UP; 4ZR1-UP; 1LS1-UP; 9ES1-UP; LRX1-UP)
3406E (S/N: 8AZ1-UP)
3408 (S/N: 67U1-11134; 78Z1-1143)
3408B (S/N: 67U11135-16070; 78Z1144-4866)
3408C (S/N: 67U16071-UP; 78Z4867-UP)
3412 (S/N: 2WJ1-UP; 38S1-16483; 4BZ1-UP; 81Z1-14500)
3412C (S/N: 9EP1-UP; 38S16484-UP; 81Z14501-UP; BCW1-UP; LRY1-UP)
3456 (S/N: BGA1-UP; CCB1-UP; GHJ1-UP; CBX1-UP)
3508 (S/N: 1ZF1-UP; CNF1-UP; PTK1-UP; 5XM1-UP; 3LS1-UP; 5PW1-UP; CAW1-UP; 23Z1-UP; 70Z1-UP)
3508B (S/N: CNB1-UP; PTJ1-UP; 4GM1-UP; 6PN1-UP; PTN1-UP; 2HW1-UP; 5KW1-UP; BGX1-UP)
3512 (S/N: 3YF1-UP; PTG1-UP; PTH1-UP; CMJ1-UP; 6PM1-UP; FDR1-UP; 3MS1-UP; 6WW1-UP; 24Z1-UP; 67Z1-UP)
3512B (S/N: CMC1-UP; BLF1-UP; PTF1-UP; BRK1-UP; 8RM1-UP; PTM1-UP; 6WN1-UP; 4AW1-UP; 5AW1-UP; 6GW1-UP; 2EZ1-UP)
3516 (S/N: CMD1-UP; PTD1-UP; 4XF1-UP; 5SJ1-UP; CAL1-UP; 7KM1-UP; 3NS1-UP; 8TW1-UP; 25Z1-UP; 73Z1-UP)
3516B (S/N: CPA1-UP; BMB1-UP; PTC1-UP; BPJ1-UP; 6HN1-UP; 7RN1-UP; FDN1-UP; 1NW1-UP; 8NW1-UP)
C-12 (S/N: BEL1-UP)
D330C (S/N: 02B1-4225; 04B1-4554)
D333C (S/N: 66D1-8890; 70R1-UP)
D379A (S/N: 68B1-1615)
D379B (S/N: 34Z1-UP; 68B1616-UP)
D398A (S/N: 66B1-UP)
D398B (S/N: 35Z1-UP; 66B2049-UP)
D399 (S/N: 35B1-UP; 36Z1-UP)
G3306 (S/N: 07Y1-UP)
G3406 (S/N: 4FD1-UP)
G3408 (S/N: 6NB1-UP)
G3412 (S/N: 7DB1-UP; 3NK1-UP)
G3508 (S/N: 4WD1-UP; 2JF1-UP; 9TG1-UP)
G3512 (S/N: 4KC1-UP; 5JD1-UP; 7NJ1-UP)
G3516 (S/N: 3RC1-UP; 8LD1-UP; 4EK1-UP)
G3524 (S/N: 7SZ1-UP)
G379 (S/N: 72B1-UP)
G398 (S/N: 73B1-UP)
G399 (S/N: 49C1-UP)
Systems Operation, Testing and Adjusting, RENR1200, "Electronic Modular Control Panel II+ (EMCPII+) for EU Engines", "GSC CID 0190 - FMI 02". This module is part of Service Manual, RENR1225, Service Manual, SENR1020 and Service Manual, RENR2295.Systems Operation, Testing and Adjusting, Troubleshooting, RENR2483, "EMCP II for Larne and Chinese Gensets", "GSC CID 0190 - FMI 02". This module is part of Service Manual, RENR2215, Service Manual, RENR2206, Service Manual, RENR1220, Service Manual, RENR1375, Service Manual, RENR1280, Service Manual, RENR1380, Service Manual, RENR2330, Service Manual, RENR1385 and Service Manual, RENR2360.Systems Operation, Testing and Adjusting, Troubleshooting, RENR2484, "EMCP II+ for Larne and Chinese Gensets", "GSC CID 0190 - FMI 02". This module is part of Service Manual, RENR2215, Service Manual, RENR2205, Service Manual, RENR1220, Service Manual, RENR1375, Service Manual, RENR1280, Service Manual, RENR1380, Service Manual, RENR2330, Service Manual, RENR1385 and Service Manual, RENR2360.Systems Operation, Testing and Adjusting, Troubleshooting, RENR2486, "EMCP II+ for Griffin 3400", "GSC CID 0190 - FMI 02". This module is part of Service Manual, RENR1385 and Service Manual, RENR2360.Systems Operation, Testing and Adjusting, Troubleshooting, SENR5828, "Electronic Modular Control Panel II (EMCPII)", "GSC CID 0190 - FMI 02". This module is part of Service Manual, SEBU6620, Service Manual, RENR2375, Service Manual, RENR2365, Service Manual, SEBU6500, Service Manual, RENR2370 and Service Manual, SEBU6440. In the above-referenced procedures, the list of possible causes of a CID 190 FMI 02 is incorrect. The corrected list of possible CID 190 FMI 02 causes is shown below. The possible causes of a CID 190 FMI 02 are listed below:
The frequency of the signal is below acceptable limits. There is a short to the battery negative terminal.
The air gap of the speed sensor is too large.
The GSC has detected a raised oil pressure but the engine speed signal indicates 0 RPM. This may occur during the started rest cycle. See Test Step 9.In the above-referenced procedures, a Test Step was omitted. Add the Test Step that is shown below.TEST STEP 9. Oil Pressure Check.Note: During the