2899501 VALVE GP-PUMP CONTROL Caterpillar parts
M313D, M315D 2
Rating:
Alternative (cross code) number:
CA2899501
289-9501
2899501
CA2899501
289-9501
2899501
Weight: 10 pounds 4 kg.
WHEELED EXCAVATOR,
Number on catalog scheme:
3
For full view, you need register
Information:
Machine Shipping
Investigate the travel route for overpass clearances. Make sure there will be adequate clearance if the machine being transported is equipped with a ROPS, cab or canopy.To prevent the machine from slipping while loading, or shifting in transit, remove ice, snow or other slippery material from the loading dock and the truck bed before loading.
Obey all state and local laws governing the weight, width and length of a load.Observe all regulations governing wide loads.
1. Block the trailer or rail car wheels before loading (trailer shown). 2. After the machine is in position, connect the steering frame lock link to hold the front and rear frames rigid. 3. Lower the bucket to the floor of the transport machine. Move the transmission control lever to NEUTRAL. 4. Engage the transmission neutral lock. 5. Engage the parking/secondary brake.6. Stop the engine. 7. Turn the start key switch to OFF and remove the key. 8. Turn the disconnect key switch to OFF and remove the key. 9. Block the tires and secure the machine with tie-downs when transporting on a rail car or a tractor-trailer. 10. Cover the exhaust opening or secure the rain cap to prevent the turbocharger from "windmilling" in transit.Machine Roading
Before roading a machine, consult your tire dealer for recommended tire pressures and speed limitations."TON km/h" (TON MPH) limitations must be observed. Consult your tire dealer for the speed limit of the tires involved.When traveling long distances, stop every 40 km (25 miles) or 1 hour for 30 minutes to allow the tires and components to cool.Inflate the tires to the correct pressure. Use a self-attaching inflation chuck and stand behind the tire tread while inflating the tire. See "Tire Inflation Information." Bring the engine coolant, the crankcase oil and the transmission oil up to the correct levels.Check with the proper officials to obtain the required permits, etc.Travel at a moderate speed. Observe all speed limitations when roading the machine.Perform a "Walk-Around Inspection" and measure the fluid levels in the various compartments.
Investigate the travel route for overpass clearances. Make sure there will be adequate clearance if the machine being transported is equipped with a ROPS, cab or canopy.To prevent the machine from slipping while loading, or shifting in transit, remove ice, snow or other slippery material from the loading dock and the truck bed before loading.
Obey all state and local laws governing the weight, width and length of a load.Observe all regulations governing wide loads.
1. Block the trailer or rail car wheels before loading (trailer shown). 2. After the machine is in position, connect the steering frame lock link to hold the front and rear frames rigid. 3. Lower the bucket to the floor of the transport machine. Move the transmission control lever to NEUTRAL. 4. Engage the transmission neutral lock. 5. Engage the parking/secondary brake.6. Stop the engine. 7. Turn the start key switch to OFF and remove the key. 8. Turn the disconnect key switch to OFF and remove the key. 9. Block the tires and secure the machine with tie-downs when transporting on a rail car or a tractor-trailer. 10. Cover the exhaust opening or secure the rain cap to prevent the turbocharger from "windmilling" in transit.Machine Roading
Before roading a machine, consult your tire dealer for recommended tire pressures and speed limitations."TON km/h" (TON MPH) limitations must be observed. Consult your tire dealer for the speed limit of the tires involved.When traveling long distances, stop every 40 km (25 miles) or 1 hour for 30 minutes to allow the tires and components to cool.Inflate the tires to the correct pressure. Use a self-attaching inflation chuck and stand behind the tire tread while inflating the tire. See "Tire Inflation Information." Bring the engine coolant, the crankcase oil and the transmission oil up to the correct levels.Check with the proper officials to obtain the required permits, etc.Travel at a moderate speed. Observe all speed limitations when roading the machine.Perform a "Walk-Around Inspection" and measure the fluid levels in the various compartments.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
307D, 308D, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312E, 312E L, 314D CR, 314D LCR, 314E CR, 314E LCR, 315D L, 316E L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320D2, 320D2...
1853441
VALVE & LINES GP-DIVERTER
M313C, M313D
M313C, M313D
1417812
VALVE GP-RELIEF
M312, M313D, M315, M315D, M315D 2, M316D, M317D 2, M318, M318D, M318D MH, M320, M322D, M322D MH
M312, M313D, M315, M315D, M315D 2, M316D, M317D 2, M318, M318D, M318D MH, M320, M322D, M322D MH
2429670
VALVE GP-PILOT
M313C, M313D, M315C, M315D, M316C, M316D, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH
M313C, M313D, M315C, M315D, M316C, M316D, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH
120G, 130G, 14G, 1673C, 215, 225, 225D, 227, 229, 231D, 235, 3114, 3116, 3208, 3304, 3306, 3306B, 518, 528, 584, 613B, 815, 920, 924G, 924GZ, 924H, 924HZ, 924K, 928H, 928HZ, 930G, 930K, 938K, 941, 950...
1090, 1190, 1190T, 120K, 120K 2, 120M, 120M 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 214B, 2...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 323D2 L, 420E, 430E, 450E, 525D, 535D, 545D, 553C, 559, 613G, 914G, 924H, 924HZ, 924K, 928H, 928HZ, 930K, 938H, 938K, 950 GC, 953D, 963D, AP-600D, AP-655D, A...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 323D2 L, 420E, 430E, 450E, 525D, 535D, 545D, 553C, 559, 613G, 914G, 924H, 924HZ, 924K, 928H, 928HZ, 930K, 938H, 938K, 950 GC, 953D, 963D, AP-600D, AP-655D, A...
120M, 12M, 2470C, 311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D...
3126E, 3208, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 613C, 933, 933C, 938G, 939, 939C, 950F, 950F II, 950G, 953C, 960F, 962G, AP-200B, AP-800C, AP-800D, B...
307D, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR,...
1U4598
VALVE GP
225
225
1589075
VALVE GP-CONTROL
307B, 315C
307B, 315C
3188451
VALVE GP
966K, 972K
966K, 972K
2542637
VALVE GP-CONTROL
M313D, M315D, M316D
M313D, M315D, M316D
1466158
VALVE GP-BANK 4
TH63, TH82, TH83
TH63, TH82, TH83
3540164
VALVE GP-RELIEF
D6T, D6T LGP, D6T LGPPAT, D6T XL, D8T, PL83
D6T, D6T LGP, D6T LGPPAT, D6T XL, D8T, PL83
2307959
VALVE GP-FLOW CONTROL
RM-300, RM-500
RM-300, RM-500