2Y2174 VALVE GROUP Caterpillar parts
120B
Rating:
Alternative (cross code) number:
CA2Y2174
2Y-2174
2Y2174
CA2Y2174
2Y-2174
2Y2174
Weight: 4 pounds 2 kg.
MOTOR GRADER,
Compatible equipment models: 2Y2174:
Number on catalog scheme:
2
For full view, you need register
Information:
Possible causes for an FMI 9 diagnostic code are:
Terminating resistors on the J1939 Data Link are faulty.
An open or a poor connection in the circuit.
A short in the circuit.
An ECM or smart device is not powering up or powering down properly.
Lack of key switch input to an ECM or smart device.
Excessive noise on the circuit.
Software configuration mismatch.
One of the ECM modules has failed. This condition is unlikely.Possible causes for an FMI 14 diagnostic code are:
Incorrect software is installed.
Incompatible software may be installed.
Interference across the data link wires.
A control module has failed. This situation is unlikely.
Illustration 1 g03433898
Schematic of the CAN Datalink
Note: The diagram above is a simplified schematic of the CAN Datalink connections. The schematic is electrically correct. However, not all of the possible harness connectors are shown. Refer to the latest revision of Electrical Schematic, UENR1138 for the complete schematic.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. Check the wiring for pinch points or abrasions. Look for and repair areas that indicate wires are exposed. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing a troubleshooting procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Identify The Active FMI Code Associated With The Data Link Code present FMI 9, proceed to Test Step 2.
FMI 14, proceed to Test Step 7.
Begin Process For FMI 9 Troubleshooting HERE
2. Check For Other Codes
A. Check for similar diagnostic codes that are logged against other electronic control modules.
B. If a similar diagnostic code is found, exit this test and perform the corresponding procedure for the other diagnostic code that is shown.
Another diagnostic code is showing. OK - Exit this procedure and perform the diagnostic procedure for the diagnostic codes that are shown.
Proceed to Test Step 8.
NOT OK - There are no other related diagnostic codes.
Proceed to Test Step 3.
3. Inspect The Harness Connections
A. Turn key start switch and disconnect switch OFF.
B. Inspect all harness connections related to the data link. Make sure that the connectors are clean and tight.
The machine harness is correct. OK - The machine harness is correct.
Proceed to Test Step 4.
NOT OK - The machine harness is not correct.
Repair: Repair
Terminating resistors on the J1939 Data Link are faulty.
An open or a poor connection in the circuit.
A short in the circuit.
An ECM or smart device is not powering up or powering down properly.
Lack of key switch input to an ECM or smart device.
Excessive noise on the circuit.
Software configuration mismatch.
One of the ECM modules has failed. This condition is unlikely.Possible causes for an FMI 14 diagnostic code are:
Incorrect software is installed.
Incompatible software may be installed.
Interference across the data link wires.
A control module has failed. This situation is unlikely.
Illustration 1 g03433898
Schematic of the CAN Datalink
Note: The diagram above is a simplified schematic of the CAN Datalink connections. The schematic is electrically correct. However, not all of the possible harness connectors are shown. Refer to the latest revision of Electrical Schematic, UENR1138 for the complete schematic.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. Check the wiring for pinch points or abrasions. Look for and repair areas that indicate wires are exposed. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing a troubleshooting procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Identify The Active FMI Code Associated With The Data Link Code present FMI 9, proceed to Test Step 2.
FMI 14, proceed to Test Step 7.
Begin Process For FMI 9 Troubleshooting HERE
2. Check For Other Codes
A. Check for similar diagnostic codes that are logged against other electronic control modules.
B. If a similar diagnostic code is found, exit this test and perform the corresponding procedure for the other diagnostic code that is shown.
Another diagnostic code is showing. OK - Exit this procedure and perform the diagnostic procedure for the diagnostic codes that are shown.
Proceed to Test Step 8.
NOT OK - There are no other related diagnostic codes.
Proceed to Test Step 3.
3. Inspect The Harness Connections
A. Turn key start switch and disconnect switch OFF.
B. Inspect all harness connections related to the data link. Make sure that the connectors are clean and tight.
The machine harness is correct. OK - The machine harness is correct.
Proceed to Test Step 4.
NOT OK - The machine harness is not correct.
Repair: Repair
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
1090, 1190, 1190T, 120, 120B, 120G, 120H, 120H ES, 120H NA, 1290T, 12F, 12G, 12H, 12H NA, 130G, 135H, 135H NA, 1390, 140, 140B, 140G, 140H, 140H NA, 143H, 14E, 14H, 16, 160H, 163H, 16G, 16H NA, 16M, 2...
120, 120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12E, 12F, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14E, ...
120B, 120G, 12G, 130G, 140B, 1673C, 1674, 1676, 1693, 215, 225, 235, 3160, 3176, 3176B, 3176C, 3196, 3208, 3304, 3306, 518, 627B, 637D, 910, 920, 930, 931B, 931C, 941, 950, 951B, 955K, 955L, 966C, 977...
120B, 140B, 215B, 225, 229D, 235, 235C, 245, 245B, 245D, 518, 528, 54, 561B, 561C, 615, 615C, 623E, 824C, 826C, 920, 930, 941, 951B, 955H, 955K, 955L, 977H, 977K, 980B, 983, D346, D348, D379B, D4D, D5...
120B, 120G, 12G, 130G, 140B, 14G, 225, 3304, 3306, 528, 561C, 814, 920, 930, 941, 950, 951B, 955K, 955L, 966C, 977K, 977L, D4D, D4E, D5, D5B, D6C, D6D, D7F
120, 120B, 12F, 140, 140B, 14E, 16, 16G, 245, 245B, 245D, 3304B, 3306, 5130, 5130B, 5230, 5230B, 561B, 561C, 572G, 578, 589, 594H, 613, 621, 621B, 621E, 621F, 621R, 623, 623E, 623F, 627, 627B, 627E, 6...
120B, 12G, 3304, 3306, 561C, 920, 941, 951B, D4D, D4E, D5, D5B, D6C
120, 120B, 12F, 140B, 561C, D5
120B, 12G, 561D, D5B
120, 120B, 12E, 140B, 14E
120, 120B, 12E
2Y2361
VALVE
120B
120B
7J6055
VALVE
14E, 16
14E, 16
7J6124
VALVE GROUP
14E, 16
14E, 16
120, 120B, 12E
120, 120B, 12E, 140B, 14E
8J6752
VALVE GROUP
120G, 12G, 130G, 16G
120G, 12G, 130G, 16G
8J1834
VALVE GROUP
12G, 16G
12G, 16G
8D8748
VALVE (relay)
12G, 14G, 16G
12G, 14G, 16G
8D5402
VALVE
12G, 16G
12G, 16G
5D7164
VALVE GROUP (Charging)
14E, 16
14E, 16