VALVE GP-CONTROL 3209036 - Caterpillar

Illustration 7 g01923553
Interior side of the cushion-hitch valve (14) 130-5300 Clip
Install a new 130-5300 Clip (14) by using the existing bolt and the washer for the hydraulic flange. Use the clip in order to secure the connector for the cushion-hitch solenoid and the new harness assembly.
Illustration 8 g01923576
Rear side of the cushion-hitch valve (1) 2W-7940 Bracket (2) 3S-2093 Cable Strap (4) 4L-6454 Bolt (7) 5P-9297 Clip (8) 5S-7379 Bolt (9) 6V-8801 Nut (11) 8M-2770 Clip (13) 8T-4896 Hard Washer (20) 4P-7581 Clip (22) 130-5300 Clip (23) 5S-7379 Bolt (24) 8T-4896 Hard Washer
Install the 2W-7940 Bracket (1) to the rear of the mounting bracket for the cushion-hitch valve.
Install the following components along the bracket:
The 130-5300 Clip (22) that was retained
The 4P-7581 Clip (20) that was retained
The 8T-4896 Hard Washer (24) that was retained
The 4L-6454 Bolt (4) that is new
The 5P-9297 Clip (7) that is new
The 3S-2093 Cable Strap (2) that is newNote: Install the 130-5300 Clip (22) so that the clip faces the bracket in order to secure the connector for the auger filter. Install the 4P-7581 Clip (20) so that the angle faces away from the 130-5300 Clip (22). Use two 3S-2093 Cable Straps in order to secure the harness to the clip. Refer to Illustration 8.
Install one 5P-9297 Clip (7) at the top of the bracket by using one 5S-7379 Bolt (8), two 8T-4896 Hard Washers (24) and one 6V-8801 Nut (9) .Note: Ensure that you use a washer on each side of the bracket.
Attach the 8M-2773 Clip (11) by using the 5S-7379 Bolt (23) and the 8T-4896 Hard Washer (24) that were retained during the disassembly. Attach the clip, the bolt, and the washer to the boss that is located at the bottom of the mounting bracket for the cushion-hitch valve.
Use a 3S-2093 Cable Strap in order to secure the connector for the arc suppressor to the main harness bundle. Ensure that the connector is down when you secure the connector.
Connect the harness to all of the clips. Refer to Illustration 8 for the correct mounting configuration.
Illustration 9 g01923613
(3) 4K-8302 Clip (25) 8M-2773 Clip
Install the 8M-2773 Clip (25) that was retained during the disassembly by using one of the bolts and washers from the clamp.
Install the 4K-8302 Clip (3) by using one of the bolts and washers from the support bracket. Refer to Illustration 9.Note: Ensure that the new harness is clipped at the locations that are marked with green tape.
Illustration 10 g01923633
(2) 3S-2093 Cable Strap (6) 4S-1962 Clip (10) 7V-6571 Grommet (12) 8T-2502 Bolt (15) 132-7551 Spacer (24) 8T-4896 Hard Washer
Install the 4S-1962 Clip (6) at the top of the case near the saddle for the pin by