3386550 VALVE GP-SEQUENCE Caterpillar parts
AD30
Rating:
Alternative (cross code) number:
CA3386550
338-6550
3386550
CA3386550
338-6550
3386550
Weight: 51 pounds 23 kg.
UNDERGROUND ART TRUCK,
Compatible equipment models: 3386550:
Number on catalog scheme:
1
For full view, you need register
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Information:
Illustration 1 g01998357
Schematic for the "Dual Pressure Relief" SolenoidThis diagnostic code is associated with the "Dual Pressure Relief" Solenoid. The FMI 05 diagnostic code means that the ECM has determined that an open exists in the circuit.The possible causes for this diagnostic code are listed below:
The signal circuit from the ECM to the solenoids is open.
The return circuit from the solenoid is open.
The internal windings for the solenoid have high impedance.
The internal windings for the solenoid are open.Note: The following test procedure may create other diagnostic codes. Clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0463 FMI 05 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.Test Step 1. CHECK THE SOLENOID
Turn the disconnect switch and the key start switch to the ON position.Note: Do not start the engine.
Disconnect the solenoid with the active diagnostic code from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire M915-PU) to contact 2 (wire M739-BU).
Observe the status of the CID 0463 FMI 05 diagnostic code.Expected Result:The CID 0463 FMI 05 diagnostic code remains active. Results:
YES - The diagnostic code remains active. The jumper wire does not affect the diagnostic code. Proceed to Test Step 2.
NO - The diagnostic is no longer active. The solenoid has failed.Repair: The solenoid has failed. Repeat this Test Step "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Verify that the new solenoid corrects the problem.STOPTest Step 2. CHECK THE HARNESS FOR AN OPEN
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the ECM.
The jumper wire that was installed in the previous Test Step remains in place.
At the machine harness connector, measure the resistance from signal contact J1-61 (wire M915-PU) to contact J1-60 (wire M739-BU).Expected Result:The resistance is less than 5.0 ohms.Results:
OK - The resistance is less than 5.0 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5000 ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: The open is in wire M915-PU or in wire M739-BU of the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS
Inspect the contacts of the harness connectors and clean the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 0463 FMI 05 diagnostic code.Expected Result:The CID 0463 FMI 05 diagnostic code is active.Results:
YES - The CID 0463 FMI 05 diagnostic code is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: Failure of the ECM is unlikely. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, the ECM may have failed. Prior to replacing
Parts valve Caterpillar catalog:
324D, 324D L, 324D LN, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 3406E, 340D L, 3456, 345C, 345C L, 345C MH, 345D, 365C, 365C L, 365...
120H, 120H ES, 120H NA, 12H, 12H ES, 12K, 135H, 135H NA, 140G, 140H, 140H NA, 140K, 140K 2, 143H, 14H, 160H, 160H ES, 160K, 163H, 16G, 16H, 16H NA, 24H, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 793B,...
140H, 143H, 14H, 14M, 160H, 163H, 16H, 16M, 24M, 3176C, 3196, 3406E, 3456, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 365B, 365B II, 365B L, 365C,...
225, 225D, 229, 229D, 231D, 345B, 345B II, 345B II MH, 345B L, 518, 5230, 619, 621, 621B, 621E, 621F, 621G, 621R, 623, 623B, 623E, 623F, 623G, 627, 627B, 627E, 627F, 627G, 631C, 631E, 631G, 633C, 633E...
621G, 623G, 627F, 627G, 627H, 627K, 627K LRC, 631G, 637G, 657G, 735, 740, 770, 772, 789D, 793D, AD30, AD45B, AD55, R1600H, SPF343C, TH48-E80
120K, 120K 2, 120M, 120M 2, 12K, 12M, 140K, 140K 2, 140M, 140M 2, 14M, 160K, 160M, 160M 2, 24M, 30/30, 3176B, 3176C, 3196, 320B, 320B L, 322 FM L, 330, 330 L, 3306, 3306B, 330B, 330B L, 345B, 345B L, ...
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140B, 140G, 140H, 140H ES, 1...
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120M, 1290T, 12G, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 1390, 140G, 140H ES, 140H NA, 143H, 14H, 14H NA, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 16...
1090, 1190, 1190T, 120, 120B, 120G, 120H, 120H ES, 120H NA, 1290T, 12F, 12G, 12H, 12H NA, 130G, 135H, 135H NA, 1390, 140, 140B, 140G, 140H, 140H NA, 143H, 14E, 14H, 16, 160H, 163H, 16G, 16H NA, 16M, 2...
3114, 3116, 3126B, 3176, 3176B, 3176C, 3196, 3406B, 3412E, 35, 3512, 45, 55, 613C, 613C II, 613G, 69D, 936, 936F, 980F, 980G, AD30, AD40, AD45, AD55, AE40, AE40 II, AP-1000B, AP-1055B, AP-1055D, AP-90...
1090, 1190, 1190T, 120H, 120K, 120K 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 1390, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M 2, 160M 3, 160M 3 AWD, 16M, 236D, 242...
120G, 650B, 666, 768B, 768C, 769, 769C, 771D, 988B, 992, AD30, AD45, AD45B, AE40 II, R1600, R1600G, R1600H, R1700 II, R1700G, R2900, R2900G
4242298
VALVE GP-RELIEF
D11R, D11T
D11R, D11T
3959657
VALVE GP-CONTROL
MH3037
MH3037