3416222 VALVE GP-BANK 7 Caterpillar parts
140K, 140K 2, 160K
Rating:
Alternative (cross code) number:
CA3416222
341-6222
3416222
CA3416222
341-6222
3416222
MOTOR GRADER,
Number on catalog scheme:
2
For full view, you need register
Information:
Introduction
This instruction gives the procedure needed to replace the 1P9946 Fan Drive Shaft.Do not perform any procedure outlined in this publication until you read and understand the information contained within.Reference: Service Manual and Parts BookNecessary Parts
* 1 1P9946 - Fan Shaft* 1 5S2106 - SealReplacement Procedure
1. Remove 6N7210 Fan Drive Group from engine. Refer to Service Manual for disassembly procedures.2. Remove grease fitting (5).3. Remove 5B5812 Dowel (1) from side (A).4. Press out 1P9946 Shaft (3) from 6N7260 Bracket Assembly (4).5. Position new 1P9946 Shaft (3) in side (C) of 6N7260 Bracket Assembly (4) with tapped holes (2) in a vertical position as shown.Press shaft (3) into bracket assembly (4) to depth shown.6. Drill a 8.7 mm (.342 in) hole through shaft (3) from side (B).7. Drill and ream a 9.340 .013 mm (.368 .0005 in) hole to a depth of 23.0 1.5 mm (.905 .059 in) from side (A).8. Install 5B5812 Dowel (1) in side (A) to depth shown.9. Install grease fitting (5) in side (B). When re-assembling 6N7210 Fan Drive Group, replace 5S2106 Seal.10. Install fan drive group. Refer to Service Manual for installation procedures.
This instruction gives the procedure needed to replace the 1P9946 Fan Drive Shaft.Do not perform any procedure outlined in this publication until you read and understand the information contained within.Reference: Service Manual and Parts BookNecessary Parts
* 1 1P9946 - Fan Shaft* 1 5S2106 - SealReplacement Procedure
1. Remove 6N7210 Fan Drive Group from engine. Refer to Service Manual for disassembly procedures.2. Remove grease fitting (5).3. Remove 5B5812 Dowel (1) from side (A).4. Press out 1P9946 Shaft (3) from 6N7260 Bracket Assembly (4).5. Position new 1P9946 Shaft (3) in side (C) of 6N7260 Bracket Assembly (4) with tapped holes (2) in a vertical position as shown.Press shaft (3) into bracket assembly (4) to depth shown.6. Drill a 8.7 mm (.342 in) hole through shaft (3) from side (B).7. Drill and ream a 9.340 .013 mm (.368 .0005 in) hole to a depth of 23.0 1.5 mm (.905 .059 in) from side (A).8. Install 5B5812 Dowel (1) in side (A) to depth shown.9. Install grease fitting (5) in side (B). When re-assembling 6N7210 Fan Drive Group, replace 5S2106 Seal.10. Install fan drive group. Refer to Service Manual for installation procedures.
Caterpillar SIS machinery equipment:
Caterpillar SIS
160K Motor Grader JBP00001-UP (MACHINE) POWERED BY C7 Engine »
341-6222
VALVE GP-BANK 7
140K Motor Grader SZL00001-UP (MACHINE) POWERED BY C7 Engine »
341-6222
VALVE GP-BANK 7
160K Motor Grader SZM00001-UP (MACHINE) POWERED BY C7 Engine »
341-6222
VALVE GP-BANK 7
140K Motor Grader JPA00001-UP (MACHINE) POWERED BY C7 Engine »
341-6222
VALVE GP-BANK 7
140K Series 2 Motor Grader SZW00001-UP (MACHINE) POWERED BY C7 Engine »
341-6222
VALVE GP-BANK 7
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
2002048
VALVE GP-TRANSMISSION CONTROL
938G II, IT38G II
938G II, IT38G II
1999690
VALVE GP-RELIEF
735, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I, TH35-C15T, TH35-E81
735, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I, TH35-C15T, TH35-E81
1606623
VALVE GP-AIR CONTROL
PS-360B
PS-360B
2627291
VALVE GP-BANK 5
120H, 120K, 120K 2, 12H, 135H, 140H, 140K, 143H, 160H, 160K, 163H
120H, 120K, 120K 2, 12H, 135H, 140H, 140K, 143H, 160H, 160K, 163H
9T1713
VALVE GP
980C
980C
3467625
VALVE GP-CONTROL
374F L, 390F L
374F L, 390F L
2542650
VALVE & LINES GP-BOOM
M322D, M322D MH
M322D, M322D MH
1575906
VALVE GP-BANK 3
35, 45, 55
35, 45, 55