AVSPARE.COM
parts catalog

VALVE GP-CONTROL 3727470 - Caterpillar



3727470 VALVE GP-CONTROL Caterpillar parts 525D, 535D, 545D, 555D VALVE
Rating:
9
Alternative (cross code) number:
CA3727470
372-7470
3727470
Caterpillar 3727470 VALVE GP-CONTROL
Weight: 16 pounds 7 kg.

Buy VALVE GP-CONTROL 3727470 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SKIDDER,

Compatible equipment models: 3727470:

WHEEL SKIDDER  525D   535D   545D   555D   Caterpillar
Number on catalog scheme: 5
 
  For full view, you need register

Information:


Illustration 8 g00480940
Apply 7M-7260 Liquid Gasket onto the seal bore of retainer (21). Use Tooling (A) and install lip seal (23). The lip of the seal should be facing toward the inside of the bore. Note: Do not put the liquid gasket on the seal case.
Illustration 9 g00477014
Position bearing retainer (21) onto bearing cage (22) and install six bolts (20) .
Illustration 10 g00477013
Install spacer (18) onto output shaft (19) .
Illustration 11 g00477012
Lower the temperature of bearing cup (17) and install the bearing cup into bearing cage (14). Install O-ring seal (16) onto bearing cage (14) .
Illustration 12 g00481042
Apply 7M-7260 Liquid Gasket onto the seal bore of bearing cage (14). Use Tooling (A) and install lip seal (15). The lip of the seal should be facing toward the inside of the bore.
Illustration 13 g00477009
Position bearing cage (14) onto transfer case (7) and install eight nuts (13). Tighten nuts to a torque of 55 10 N m (40 7 lb ft).
Illustration 14 g00477007
Lower the temperature of bearing cup (12) and install bearing cup (12) into transfer case (7) .
Illustration 15 g00481363
Heat two bearings (11) to a maximum temperature of 135°C (275°F). Install two bearings (11) onto each side of gear assembly (10). Use two persons and install gear assembly (10) into transfer case (7). Gear assembly (10) weighs approximately 23 kg (50 lb).
Illustration 16 g00477004
Lower the temperature of bearing cup (8) and install bearing cup (8) into cage assembly (5) .
Illustration 17 g00481369
Install cage assembly (5) onto transfer case (7) without the O-ring seal or the shims and install twelve bolts (3). Tighten the bolts to a torque of 7 N m (5 lb ft). Use Tooling (B) in order to measure gap clearance between cage assembly (5) and transfer case (7). Clearance should be .10 .05 mm (0.004 0.002 inch). Add the shims in order to adjust proper clearance.
Illustration 18 g00481372
Remove twelve bolts (3) and remove cage assembly (5). Install the O-ring seal onto cage assembly (5). Apply a small amount of clean power train oil onto the O-ring seal.
Illustration 19 g00481365
Install shims (9) onto transfer case (7) .
Illustration 20 g00477001
Position cage assembly (5) and two lifting eyes (4) and install twelve bolts (3). Position cover (2) and the O-ring seal and install two bolts (1) .End By: Connect the transmission to the transfer gears. Refer to Disassembly and Assembly, "Transmission and Transfer Gears - Connect". The information is in this manual.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
525D WHEEL SKIDDER GKP00001-UP (MACHINE) POWERED BY C7.1 Engine
535D WHEEL SKIDDER MTP00001-UP (MACHINE) POWERED BY C7.1 Engine
545D WHEEL SKIDDER KGP00001-UP (MACHINE) POWERED BY C7.1 Engine
555D WHEEL SKIDDER PGY00001-UP (MACHINE) POWERED BY C7.1 Engine
525D WHEEL SKIDDER 2L500001-UP (MACHINE) POWERED BY C7.1 Engine
535D WHEEL SKIDDER 3L500001-UP (MACHINE) POWERED BY C7.1 Engine
545D WHEEL SKIDDER 4L500001-UP (MACHINE) POWERED BY C7.1 Engine
555D WHEEL SKIDDER 5L500001-UP (MACHINE) POWERED BY C7.1 Engine
525D WHEEL SKIDDER (OEM) RD500001-UP (MACHINE) POWERED BY C7.1 Engine


Parts valve Caterpillar catalog:

2391134 VALVE GP-ETHER STARTING
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140G, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 16M, 2290...
1589956 VALVE GP-CHECK
120M, 12M, 140M, 14M, 160M, 16M, 24M, 525B, 525C, 525D, 535B, 535C, 535D, 545, 545C, 545D, 555D, 621F, 621G, 621H, 623H, 627F, 627G, 627H, 631E, 631G, 637E, 637G, 657G, 725, 725C, 730, 730C, 735, 735B...
8C3446 VALVE-FLUID SAMPLING
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140B, 140G, 140H, 140H ES, 1...
6V7238 VALVE-SHUTOFF
1090, 1190, 1190T, 120K, 120K 2, 120M, 120M 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 214B, 2...
1645590 VALVE GP-FLUID SAMPLING
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 1290T, 12H, 12K, 135H, 135H NA, 1390, 140H, 140K, 140K 2, 143H, 14H, 160H, 160K, 163H, 16H, 216B, 216B3, 226B, 226B3, 2290, 232B, 236B, 236B3, ...
3096678 VALVE-INLET
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 323D2 L, 420E, 430E, 450E, 525D, 535D, 545D, 553C, 559, 613G, 914G, 924H, 924HZ, 924K, 928H, 928HZ, 930K, 938H, 938K, 950 GC, 953D, 963D, AP-600D, AP-655D, A...
3399637 VALVE-EXHAUST
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 323D2 L, 420E, 430E, 450E, 525D, 535D, 545D, 553C, 559, 613G, 914G, 924H, 924HZ, 924K, 928H, 928HZ, 930K, 938H, 938K, 950 GC, 953D, 963D, AP-600D, AP-655D, A...
3K6905 VALVE-BREATHER
140G, 3126, 3126B, 3208, 3412, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, 5130, 5130B, 515, 518, 5230, 5230B, 525, 525B, 525C, 525D, 528, 528B, 530B, 533, 535B...
2D5802 VALVE-BALL
120, 12E, 140, 14E, 16, 235C, 3618, 525B, 525C, 525D, 533, 535B, 535C, 535D, 543, 545, 545C, 545D, 555D, 631E, 637D, 637E, 651E, 657E, 769, 816, 824, 824B, 826B, 834, 988, C175-16, HA770, HA771, HA870...
3496734 VALVE GP-EXHAUST GAS (NRS)
120M 2, 2384C, 2484C, 2570C, 2670C, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 525D, 535D, 545D, 555D, 559C, 563C, 573C, 579C, 924K, 930K, 938K, 95...
3D2239 VALVE AS-TIRE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 130G, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 160H, 160K, 160M...
8U2202 VALVE GP
206B, 212B, 214B, 224B
3350169 VALVE GP-SOLENOID & RELIEF
320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN
9T8482 VALVE GP-RELIEF
416, 426, 428, 436, 438
2144805 VALVE GP-PUMP CONTROL
CS-533D, CS-563D, CS-563E
2399036 VALVE GP-CHECK
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L
3050025 VALVE GP-RELIEF
613G, 621H, 621K, 627H, 627K, 627K LRC
9P9635 VALVE GP-SELECTOR & PRESS CONT
910, 916, G910, G916, IT12, IT18B
2088451 VALVE GP-CONTROL
MP15, P360, S305, S365B, S365C, S465, VHC-30, VHS-50, VHS-60/3, VHS-60/4, VT30, VT50
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.