3P3774 VALVE Caterpillar parts
D5B, D6D, D7G, D8K, D9H
Rating:
Alternative (cross code) number:
CA3P3774
3P-3774
3P3774
CA3P3774
3P-3774
3P3774
Weight: 0.70 pounds 0 kg.
TRACK-TYPE TRACTOR,
Number on catalog scheme:
34
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(1)A 9U-6198 Crankshaft Turning Too 1
(2)A 9U-7336 Housing As 1
5P-7305 Engine Turning Tool 1
B 1U-7262 Telescopic Magnet 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the correct procedure.
Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure. Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to gain access to appropriate lifters (1).
Illustration 1 g01340518
Use Tooling (B) in order to remove lifters (1). Note: Place a temporary identification mark on each lifter in order to identify the correct location.
Repeat Step 1 and Step 2 in order to remove the remaining lifters. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
(1)A 9U-6198 Crankshaft Turning Too 1
(2)A 9U-7336 Housing As 1
5P-7305 Engine Turning Tool 1
B 1U-7262 Telescopic Magnet 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
It is strongly recommended that all lifters should be replaced when a new camshaft is installed.
Clean the lifters. Follow Step 1.a through Step 1.c in order to inspect the lifters. Replace any worn lifters or damaged lifters.
Inspect the seat of the pushrod in the lifter for visual wear or damage.
Inspect the shank of the lifter for wear or damage. Refer to Specifications, "Lifter Group" for more information.
Inspect the face of the lifter that runs on the camshaft for visual wear or damage.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft to access to the cylinder block in order to install appropriate lifters (1).
Lubricate lifters (1) with clean engine oil.
Illustration 2 g01340518
Use Tooling (B) to install lifters (1) to the cylinder block. Ensure that used lifters are installed in the correct location. Note: The lifters should be free to rotate.
Repeat Step 1 and Step 4 in order to install the remaining lifters. End By:
Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure.
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
(1)A 9U-6198 Crankshaft Turning Too 1
(2)A 9U-7336 Housing As 1
5P-7305 Engine Turning Tool 1
B 1U-7262 Telescopic Magnet 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the correct procedure.
Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure. Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to gain access to appropriate lifters (1).
Illustration 1 g01340518
Use Tooling (B) in order to remove lifters (1). Note: Place a temporary identification mark on each lifter in order to identify the correct location.
Repeat Step 1 and Step 2 in order to remove the remaining lifters. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
(1)A 9U-6198 Crankshaft Turning Too 1
(2)A 9U-7336 Housing As 1
5P-7305 Engine Turning Tool 1
B 1U-7262 Telescopic Magnet 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
It is strongly recommended that all lifters should be replaced when a new camshaft is installed.
Clean the lifters. Follow Step 1.a through Step 1.c in order to inspect the lifters. Replace any worn lifters or damaged lifters.
Inspect the seat of the pushrod in the lifter for visual wear or damage.
Inspect the shank of the lifter for wear or damage. Refer to Specifications, "Lifter Group" for more information.
Inspect the face of the lifter that runs on the camshaft for visual wear or damage.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft to access to the cylinder block in order to install appropriate lifters (1).
Lubricate lifters (1) with clean engine oil.
Illustration 2 g01340518
Use Tooling (B) to install lifters (1) to the cylinder block. Ensure that used lifters are installed in the correct location. Note: The lifters should be free to rotate.
Repeat Step 1 and Step 4 in order to install the remaining lifters. End By:
Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure.
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install" for the correct procedure.
Cat SIS web machinery list:
Parts valve Caterpillar catalog:
227, 229D, 322C, 325B L, 518, 528, 528B, 530B, 561D, 589, 615, 615C, 621, 621B, 621R, 623E, 627B, 637E, 651E, 657E, 814, 814B, 815, 815B, 910, 931B, 943, 950, 953, 966C, 966D, 966R, 977K, 977L, 980B, ...
140, 14E, 814, 815, 816, 966C, D6C, D6D
120B, 12G, 561D, D5B
528, 966C, 977L, D6D
12G, 140G, 3306, 561D, D5B
594H, D9H
594H, D9H
140G, 14G, 528, 561D, D5B, D6D
572G, 572R, 572R II, 578, 583R, 587R, 587T, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7F, D7G, D7H, D7R, D7R II, D7R XR, D8H, D8K, D8N, D8R, D9G, PL87
561D, 572G, 583K, 594, 594H, 977L, 983, 983B, D5B, D5E, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7G, D7G2, D8H, D8K, D9G, D9H
572G, D6C, D6D, D6E, D6G2 LGP, D6G2 XL, D7G, D7G2
594, D7F, D8H, D8K
1U2642
VALVE ASSEM.
963, 973
963, 973
6V0656
VALVE
D6D
D6D
3G8096
VALVE
943, 953
943, 953
3G5972
VALVE GROUP
173B, 183B, D7G, D9H
173B, 183B, D7G, D9H
772B, 773B, 824B, 825B, 920, 930, 931B, 935B, 988, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CS-431C, CS-531C, CS-533C, CS-563C, CS-573C, CS-583C, PF-300C, PS-300B
2A8577
VALVE
D5B
D5B
8J8548
VALVE GROUP
183B, D7G, D8K
183B, D7G, D8K
1J9649
VALVE
191, 572G, 583H, 594
191, 572G, 583H, 594
1J9908
VALVE GROUP
572G, 583H, 594
572G, 583H, 594
D10N, D10R, D5B, D6D, D7G, D9N
5P3554
VALVE GROUP
583K
583K
2P5089
VALVE ASSEM.
D8H, D8K
D8H, D8K