VALVE GRINDING 5P4340 - Caterpillar

Articulated Truck: D400D (S/N: 8TF1-UP)Landfill Compactor: 826C (S/N: 87X1-UP) 826H (S/N: AWF1-UP)Gas Engine: G3408 (S/N: 6NB1-UP) G3412 (S/N: 7DB1-UP) G3412C (S/N: 6ZM1-UP)Generator Set: 3406C GEN SET (S/N: C2G1-UP) 3408C (S/N: TAM1-UP) 3412 (S/N: 4BZ1-UP)Generator Set Engine: 3412 (S/N: 81Z1-UP)Industrial Engine: 3408 (S/N: 67U1-UP) 3412 (S/N: 38S1-UP) 3412C (S/N: 8AR1-UP) 3412E (S/N: 4CR1-UP) 3406 IND (S/N: 90U1-UP) C15 IND (S/N: JRE1-UP) D342C IND (S/N: 05A1-UP)Marine Engine: 3408 (S/N: 99U1-UP) 3408C MARINE (S/N: 9ER1-UP) 3412 (S/N: 60M1-UP; 3JK1-UP; 7BL1-UP) 3412E MARINE (S/N: 9KS1-UP) C30 MARINE (S/N: CLX1-UP) C32 MARINE (S/N: RNC1-UP)On-Highway Engine: 3406 (S/N: 4CK1-UP; 3ZJ1-UP) 3406B (S/N: 4MG1-UP; 7FB1-UP) 3406C TRUCK (S/N: 8PN1-UP) C-15 (S/N: MBN1-UP; 9NZ1-UP) C-16 (S/N: 7CZ1-UP)Excavator: 245 (S/N: 94L1-UP; 82X1-UP) 245B (S/N: 6MF1-UP) 345B (S/N: 5WS1-UP)Motor Grader: 16G (S/N: 93U1-UP)Off-Highway Truck/Tractor: 769C (S/N: 01X1-UP) 773B (S/N: 63W1-UP)Quarry Truck: 775B (S/N: 7XJ1-UP) 775D (S/N: 6KR1-UP; 8AS1-UP)Track-Type Tractor: D10N (S/N: 2YD1-UP; 3SK1-UP) D10R (S/N: 3KR1-UP; AKT1-UP) D8L (S/N: 7YB1-UP; 53Y1-UP) D8N (S/N: 5TJ1-UP) D9L (S/N: 14Y1-UP) D9N (S/N: 1JD1-UP) D9R (S/N: ABK1-UP; ACL1-UP; 8BL1-UP)Underground Articulated Truck: AD45 (S/N: BKZ1-UP)Wheel Dozer: 824C (S/N: 85X1-UP) 834B (S/N: 92Z1-UP) 844 (S/N: 2KZ1-UP)Wheel Loader: 950 (S/N: 81J1-UP) 980C (S/N: 13B1-UP) 980F (S/N: 3HK1-UP) 988B (S/N: 50W1-UP; 62Y1-UP) 988F (S/N: 8YG1-UP) 990 (S/N: 7HK1-UP) 992C (S/N: 42X1-UP; 49Z1-UP) 992D (S/N: 7MJ1-UP)Wheel Tractor-Scraper: 621B (S/N: 45P1-UP) 621E (S/N: 2PD1-UP) 623B (S/N: 46P1-UP) 631E (S/N: 1AB1-UP) 637D (S/N: 23W1-UP; 27W1-UP) 637E (S/N: 1FB1-UP; 1JB1-UP) 651E (S/N: 89Z1-UP) 657E (S/N: 90Z1-UP)Introduction
Do not perform any procedure in this document until you read this information and you understand this information. The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.Problem
Some remanufactured water pumps have been assembled with an insufficient torque. The insufficient torque is on the bolt that fastens the impeller to the shaft. The insufficient torque may cause the impeller to come loose during operation. This could cause the water pump not to work properly. Engine overheating may also occur if the water pump does not work properly.Solution
Illustration 1 g01372842
(1) The bolt for the ImpellerThe following part numbers are the water pumps that may have an insufficient torque on the bolt for the impeller.
10R-0482 Water Pump Gp
10R-0483 Water Pump Gp
10R-0484 Water Pump Gp
0R-4679 Water Pump Gp
0R-4680 Water Pump Gp
0R-8799 Water Pump Gp
0R-8800 Water Pump Gp Check the date code on the box of the remanufactured water pumps that are listed above. If the date code is January 2007, then the torque for the bolt (1) should be checked. Secure the drive gear before you torque the bolt (1). Securing the drive gear will prevent the shaft from turning while the bolt is being torqued. Make sure that the bolt (1) is torqued to 39 3 N m (28 2 lb ft).Note: The format for the date code is explained below. DDMMYYXXX. DD is equal to the day of the month. MM is equal to the month of the year. YY is equal to the year. XXX is equal to