9Q5691 VALVE Caterpillar parts
323D L, 323D LN, 325D, 329D L, 330C, 330D, 330D L, 336D L, 336D LN, 336E, 345C L, 345D, 349D L, 365C L, 385C, OEMS
Rating:
Alternative (cross code) number:
CA9Q5691
9Q-5691
9Q5691
CA9Q5691
9Q-5691
9Q5691
Weight: 0.56 pounds 0 kg.
EXCAVATOR, UNDERCARRIAGE,
Compatible equipment models: 9Q5691:
Number on catalog scheme:
10
For full view, you need register
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 1 g02319675
If the original piston is assembled, follow Step 2.a through Step 2.e in order to install the piston rings.
Position the spring for oil control ring (3) into the oil ring groove in piston (4). The central wire must be located inside the end of the spring.
Position the oil control ring with the word "TOP" in the upward position. Use Tooling (B) to install oil control ring (3) over the piston and the spring. Note: Ensure that the central wire is 180 degrees from the ring gap.
Use Tooling (B) to install intermediate compression ring (2) into the second groove in piston (4). The word "TOP" must be upward. The chamfer on the inner face must be downward. Refer to Illustration 1
Use Tooling (B) to install top compression ring (1) into the top groove in piston (4). The word "TOP" must be upward. Note: Ensure that the top compression ring is installed with Chamfer (W) in the upward position.
Position the piston ring gaps at approximately 120 degrees away from each other. Note: A new piston assembly is supplied with new piston rings.
Illustration 2 g02210673
Illustration 3 g02090053
Removal of the piston pin bushing in the connecting rod must be carried out by personnel with the correct training. Also special machinery is required. For more information refer to your authorized Caterpillar dealer.
If connecting rod assembly (6), bushing (8) and piston pin (7) are replaced, refer to Specifications, "Connecting Rod" for further information.
Lubricate bushing (8) for piston pin (7) in the connecting rod with clean engine oil. Lubricate the bore for the piston pin in piston (4) with clean engine oil.
Place piston (4) on a suitable surface with the crown downward. Position connecting rod (6) with forged Mark (X) to the square boss (14) on the piston. Ensure that slot (13) on the connecting rod is in the correct position. See Illustration 3.
Install piston pin (7) to piston (4). Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (A) in order to install circlips (5) to the piston pin bore in piston (4). Note: Ensure that the circlips are seated in the grooves in the piston.
Install upper bearing shell (9) into connecting rod (6). Ensure that the locating tab for the upper bearing shell is correctly seated in slot (13) in the connecting rod.
Install lower bearing shell (10) into connecting rod cap (11). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Fracture split connecting rods should not be left without the connecting rod caps installed. Temporarily install connecting rod cap (11) and bolts
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 1 g02319675
If the original piston is assembled, follow Step 2.a through Step 2.e in order to install the piston rings.
Position the spring for oil control ring (3) into the oil ring groove in piston (4). The central wire must be located inside the end of the spring.
Position the oil control ring with the word "TOP" in the upward position. Use Tooling (B) to install oil control ring (3) over the piston and the spring. Note: Ensure that the central wire is 180 degrees from the ring gap.
Use Tooling (B) to install intermediate compression ring (2) into the second groove in piston (4). The word "TOP" must be upward. The chamfer on the inner face must be downward. Refer to Illustration 1
Use Tooling (B) to install top compression ring (1) into the top groove in piston (4). The word "TOP" must be upward. Note: Ensure that the top compression ring is installed with Chamfer (W) in the upward position.
Position the piston ring gaps at approximately 120 degrees away from each other. Note: A new piston assembly is supplied with new piston rings.
Illustration 2 g02210673
Illustration 3 g02090053
Removal of the piston pin bushing in the connecting rod must be carried out by personnel with the correct training. Also special machinery is required. For more information refer to your authorized Caterpillar dealer.
If connecting rod assembly (6), bushing (8) and piston pin (7) are replaced, refer to Specifications, "Connecting Rod" for further information.
Lubricate bushing (8) for piston pin (7) in the connecting rod with clean engine oil. Lubricate the bore for the piston pin in piston (4) with clean engine oil.
Place piston (4) on a suitable surface with the crown downward. Position connecting rod (6) with forged Mark (X) to the square boss (14) on the piston. Ensure that slot (13) on the connecting rod is in the correct position. See Illustration 3.
Install piston pin (7) to piston (4). Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (A) in order to install circlips (5) to the piston pin bore in piston (4). Note: Ensure that the circlips are seated in the grooves in the piston.
Install upper bearing shell (9) into connecting rod (6). Ensure that the locating tab for the upper bearing shell is correctly seated in slot (13) in the connecting rod.
Install lower bearing shell (10) into connecting rod cap (11). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Fracture split connecting rods should not be left without the connecting rod caps installed. Temporarily install connecting rod cap (11) and bolts
Cat SIS web machinery list:
Parts valve Caterpillar catalog:
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 307, 307B, 307C, 308C, 311B, 311C, 312, 312B, 312B L, 312C L, 312D, 313B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 317B LN, 318B, 318C, 319C, 319D,...
305.5, 306, 306E, 307B, 307C, 307D, 308C, 308D, 311, 311B, 311C, 311D LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 313B, 314C, 314D CR, 314D LCR, 315, 315B, 315B L, 315C, 315D L, 317B LN, 318B, 318C...
311B, 312B, 312C, 312C L, 315C, 318B, 318C, 319C, 320B, 320C, 320C FM, 320C L, 322C, 325B, 325C, 330C, 330C L, 345B II, 350, 365B, 365B L, 375, 385B
1290T, 1390, 2491, 2590, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D...
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 3...
312C, 312C L, 315C, 318C, 319C, 320C, 320C FM, 320C L, 320D, 320D FM RR, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 322C, 323D L, 323D LN, 324D, 325C, 325D, 325D L, 330C, 330C L, 330D, 330D L
318C, 319C, 320, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, ...
307D, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR,...
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D LN, 323D SA
120G, 140G, 14G, 16G
120G, 140G, 14G, 160G, 16G
8J5886
VALVE GP
120G, 130G, 140G, 14G, 16G
120G, 130G, 140G, 14G, 16G
120G, 130G, 140G, 14G, 160G, 16G
8J8385
VALVE GP
120G, 140G, 14G, 160G, 16G
120G, 140G, 14G, 160G, 16G
120G, 12G, 130G, 140G, 14G, 16G
9T1871
VALVE GP
120G, 12G, 130G, 140G, 14G
120G, 12G, 130G, 140G, 14G
6E1988
VALVE GP
120G, 12G, 130G, 140G, 160G, 16G
120G, 12G, 130G, 140G, 160G, 16G
1907745
VALVE GP-CHECK
330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
2446346
VALVE
330C, 330D L, 336D L
330C, 330D L, 336D L
1163499
VALVE
330, 330 L, 345B, 345B L, 350, 350 L, 365B, 365B L, 374F L, OEMS
330, 330 L, 345B, 345B L, 350, 350 L, 365B, 365B L, 374F L, OEMS
1163497
VALVE AS
330, 330 L, 345B, 345B L, 350, 350 L, OEMS
330, 330 L, 345B, 345B L, 350, 350 L, OEMS