3G7633 VANE PUMP GROUP Caterpillar parts
633D
Rating:
Alternative (cross code) number:
CA3G7633
3G-7633
3G7633
CA3G7633
3G-7633
3G7633
Weight: 100 pounds 45 kg.
WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$1,327.83
04 Aug 2018
Flint Hydraulics: Flint Hydraulic
3G7633 - CAT REPLACEMENT HYD PUMP
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 3G7633:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".Note: A hydraulic oil sample should be obtained before any maintenance is performed in order to establish the system contaminant level. Refer to Fluid Analysis Laboratory Guide, SEBF3116, "Obtaining an Oil Sample for S O S Analysis". Refer to Operation and Maintenance Manual, "Sampling Interval and Location of Sampling Valve" for the correct location.
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00690963
Remove the cap from the hydraulic tank. Attach Tooling (A) to the hydraulic tank. Apply 344 70 kPa (50 10 psi) to Tooling (A).
Illustration 2 g01220136
Remove bolts (1) and the washers in order to remove cover (2) .
Illustration 3 g00953950
Disconnect hose assemblies (5) and (7) .
Remove bolts (3) .
Remove bolts (4) and remove drift reduction valve (6) .
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".Note: A hydraulic oil sample should be obtained before any maintenance is performed in order to establish the system contaminant level. Refer to Fluid Analysis Laboratory Guide, SEBF3116, "Obtaining an Oil Sample for S O S Analysis". Refer to Operation and Maintenance Manual, "Sampling Interval and Location of Sampling Valve" for the correct location.
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00690963
Remove the cap from the hydraulic tank. Attach Tooling (A) to the hydraulic tank. Apply 344 70 kPa (50 10 psi) to Tooling (A).
Illustration 2 g01220136
Remove bolts (1) and the washers in order to remove cover (2) .
Illustration 3 g00953950
Disconnect hose assemblies (5) and (7) .
Remove bolts (3) .
Remove bolts (4) and remove drift reduction valve (6) .
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts vane Caterpillar catalog:
631C, 633C, 633D, 637
1U0422
VANE PUMP GROUP
633D, 639D
633D, 639D
3G6826
VANE PUMP GROUP
633D, 639D
633D, 639D
633D, 639D
1U0422
VANE PUMP GROUP
633D, 639D
633D, 639D
7J6258
VANE PUMP GROUP
631C, 633C, 637
631C, 633C, 637
8J8484
VANE PUMP GROUP
140, 141
140, 141
983, 983B
633D, 639D
3G6826
VANE PUMP GROUP
633D, 639D
633D, 639D