3N2756 VEE BELT SET Caterpillar parts
3304, 3306
Rating:
Alternative (cross code) number:
CA3N2756
3N-2756
3N2756
CA3N2756
3N-2756
3N2756
Weight: 2 pounds 1 kg.
GEN SET ENGINE, INDUSTRIAL ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
D&D PowerDrive 3N2756 Caterpillar Replacement Belt, Rubber, 54.27" Length
D&D PowerDrive Belt 17.53 x 54.27in OC || Material type- rubber || Manufactured by D&D PowerDrive || Made in China
D&D PowerDrive Belt 17.53 x 54.27in OC || Material type- rubber || Manufactured by D&D PowerDrive || Made in China
D&D PowerDrive 3N2756 Caterpillar Replacement Belt, Rubber, 54.27" Length
D&D PowerDrive Belt 17.53 x 54.27in OC || Material type- rubber || Manufactured by D&D PowerDrive || Made in China
D&D PowerDrive Belt 17.53 x 54.27in OC || Material type- rubber || Manufactured by D&D PowerDrive || Made in China
One New Automotive Wedge Belt Fits Allis Chalmers, Fits Ford, Fits New Holland 3000, 6060, 6070, 6080 Models Interchangeable With 1154358, 13X1370, 17540, 17541, 25-9540, 259540, 379966R2, 3N2756, 4N6
Stevens Lake Parts Oc Length: 54.27" || Lp Length : 54" || (17/32" X 54.27") || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product.
Stevens Lake Parts Oc Length: 54.27" || Lp Length : 54" || (17/32" X 54.27") || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product.
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 111-5051 Wrench 1
B 4C-6161 Tube Brush 1
164-5927 Wire Brush 1
9U-6102 Reamer 1
C 164-5924 Injector Bore Gauge 1
D 5P-3931 Anti-Seize Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00337772
This is an example of a typical injector sleeve. (1) 120 degree angled surface of the injector sleeve. The lower O-ring seal on the injector contacts the injector sleeve in this area. (2) The injector tip fits in this bore in the injector sleeve.Cleanliness is essential to the proper sealing of the injector. All carbon deposits should be removed from the injector sleeve and the bore (2) . Carbon deposits should also be removed from the 120 degree angled surface (1) at the bottom of the injector sleeve.
Failure to properly clean any of the listed areas may cause an improper seal at the lower injector O-ring seal. This could result in tip damage or injector failure due to leakage of combustion gas into the fuel passage.
Use Tooling (B) to clean the carbon deposits from bore (2) of the injector sleeve.After the injector sleeve has been cleaned with Tooling (B) , use Tooling (C) to determine that an adequate amount of carbon has been removed. Refer to Disassembly and Assembly, "Unit Injector - Install".
Illustration 2 g00555510
Install new O-ring seals (2) and washer (3) on the unit injector sleeve (1) .
Lubricate O-ring seals (2) with clean engine oil.
Illustration 3 g00555505
Apply Tooling (D) to unit injector sleeve (1) . Install the unit injector sleeve in the cylinder head and tighten to a torque of 100 10 N m (74 7 lb ft) with Tooling (A) .
Fill the engine with coolant. Refer to Operation and Maintenance Manual, "Lubricant Viscosities and Refill Capacities".End By:
Install the unit injector. Refer to Disassembly and Assembly, "Unit Injector - Install".
Install the rocker arm and shaft. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 111-5051 Wrench 1
B 4C-6161 Tube Brush 1
164-5927 Wire Brush 1
9U-6102 Reamer 1
C 164-5924 Injector Bore Gauge 1
D 5P-3931 Anti-Seize Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00337772
This is an example of a typical injector sleeve. (1) 120 degree angled surface of the injector sleeve. The lower O-ring seal on the injector contacts the injector sleeve in this area. (2) The injector tip fits in this bore in the injector sleeve.Cleanliness is essential to the proper sealing of the injector. All carbon deposits should be removed from the injector sleeve and the bore (2) . Carbon deposits should also be removed from the 120 degree angled surface (1) at the bottom of the injector sleeve.
Failure to properly clean any of the listed areas may cause an improper seal at the lower injector O-ring seal. This could result in tip damage or injector failure due to leakage of combustion gas into the fuel passage.
Use Tooling (B) to clean the carbon deposits from bore (2) of the injector sleeve.After the injector sleeve has been cleaned with Tooling (B) , use Tooling (C) to determine that an adequate amount of carbon has been removed. Refer to Disassembly and Assembly, "Unit Injector - Install".
Illustration 2 g00555510
Install new O-ring seals (2) and washer (3) on the unit injector sleeve (1) .
Lubricate O-ring seals (2) with clean engine oil.
Illustration 3 g00555505
Apply Tooling (D) to unit injector sleeve (1) . Install the unit injector sleeve in the cylinder head and tighten to a torque of 100 10 N m (74 7 lb ft) with Tooling (A) .
Fill the engine with coolant. Refer to Operation and Maintenance Manual, "Lubricant Viscosities and Refill Capacities".End By:
Install the unit injector. Refer to Disassembly and Assembly, "Unit Injector - Install".
Install the rocker arm and shaft. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Install".
Caterpillar parts catalog:
Parts vee Caterpillar catalog:
9L4654
VEE BELT SET
1693, 3304
1693, 3304
D349
777, 977H, D348
D343
9L0696
VEE BELT SET
1673
1673
9L1502
VEE BELT
1673
1673
D353C
D346
3N0860
VEE BELT
D346
D346
D343, D35HP, D400
D348