1045604 WASHER Caterpillar parts
3408B, 3408C, 3412, 3412C, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 906H, 908H, 924H, BP22, PM3412, SCT673, SPS342, SPT342
Rating:
Alternative (cross code) number:
CA1045604
104-5604
1045604
CA1045604
104-5604
1045604
Weight: 0.01 pounds 0 kg.
Information:
ID
7.2
mm
MATERIAL
Steel Rc C36-42
MATL THK
2
mm
OD
25
mm
COATING/PLATING
Phosphate and Oil Coating
ARTICULATED TRUCK, WHEEL LOADER,
Number on catalog scheme:
16
For full view, you need register
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01119759
Loosen jam nut (8) and adjustment screw (7). Loosen jam nut (10) and adjustment screw (9).
Illustration 2 g01131377
Illustration 3 g01158612
Valve bridge for dowel installations
Illustration 4 g01946786
Floating valve bridge
(X) Round pocket
(Y) Slotted pocket
(Z) Outside of engine
Apply clean engine oil to pushrod (5).
Apply clean engine oil to valve pushrods (4), and the cup of the valve lifters. Install valve pushrods (4) in the original location.
Valve bridge assemblies for dowel installations have an adjustment screw and a jam nut. Use the following procedure to install this configuration.
Loosen adjustment screw (11) and jam nut (12) on bridge assembly (3).
Coat these items with clean engine oil: the dowels, the receptacle of the bridge assembly for the dowels and the uppermost contact surface of bridge assembly (3).
Place bridge assembly (3) into position on the dowel. Apply a downward force of 5 to 45 N (1 to 10 lb) on the uppermost contact surface of bridge assembly (3). While you apply the force, turn adjustment screw (11) until the adjustment screw contacts the valve stem.
Turn the adjustment screw for an additional 20 to 30 degrees (1/3 to 1/2 of the hex).
Hold the adjustment screw in position and tighten jam nut (12) to a torque of 30 4 N m (22 3 lb ft).
For floating valve bridge assemblies, use the following procedure.
Apply clean engine oil to the contact surface of bridge assemblies (3) and the valve stems. Install bridge assemblies (3) on the valve stems.
Install the bridge assemblies with the round pocket toward the outside of the engine. Refer to Illustration 4.
Ensure that the crankshaft and the camshafts are in time with each other. Also ensure that the adjustment screws in the rocker arms are loosened completely before the bolts on the rocker shaft are tightened or damage to the valves and the pistons may occur.
If the rocker shaft is not positioned correctly, the oil supply to the sleeve bearings in the rocker arm will be shut off. This will cause seizure of the bearings and severe damage to the engine.Be sure to orient the rocker shaft in the correct position.
Place rocker shaft assembly (2) in position on valve mechanism cover base (6). Make sure that valve pushrods (4) and pushrod (5) are aligned with the rocker arms. Install bolts (1). Tighten the bolts evenly to a torque of 215 40 N m (160 30 lb ft).Note: The rocker shaft dowel must be located on the left-hand side of the rocker shaft when installed.
Illustration 5 g01119849
Adjust the valve lash according to Testing and Adjusting, "Valve Lash and Valve Bridge Adjustment". Hold adjustment screw (7) of the rocker arm assembly and tighten jam nut (8) to a torque of 70 15 N m (52 11 lb ft).
Adjust the electronic unit injector lash according to Testing and Adjusting, "Fuel Injector Adjustment". Hold adjustment screw (9) of the rocker arm assembly and tighten nut (10). If nut (10) is 5/8 inch thread,
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01119759
Loosen jam nut (8) and adjustment screw (7). Loosen jam nut (10) and adjustment screw (9).
Illustration 2 g01131377
Illustration 3 g01158612
Valve bridge for dowel installations
Illustration 4 g01946786
Floating valve bridge
(X) Round pocket
(Y) Slotted pocket
(Z) Outside of engine
Apply clean engine oil to pushrod (5).
Apply clean engine oil to valve pushrods (4), and the cup of the valve lifters. Install valve pushrods (4) in the original location.
Valve bridge assemblies for dowel installations have an adjustment screw and a jam nut. Use the following procedure to install this configuration.
Loosen adjustment screw (11) and jam nut (12) on bridge assembly (3).
Coat these items with clean engine oil: the dowels, the receptacle of the bridge assembly for the dowels and the uppermost contact surface of bridge assembly (3).
Place bridge assembly (3) into position on the dowel. Apply a downward force of 5 to 45 N (1 to 10 lb) on the uppermost contact surface of bridge assembly (3). While you apply the force, turn adjustment screw (11) until the adjustment screw contacts the valve stem.
Turn the adjustment screw for an additional 20 to 30 degrees (1/3 to 1/2 of the hex).
Hold the adjustment screw in position and tighten jam nut (12) to a torque of 30 4 N m (22 3 lb ft).
For floating valve bridge assemblies, use the following procedure.
Apply clean engine oil to the contact surface of bridge assemblies (3) and the valve stems. Install bridge assemblies (3) on the valve stems.
Install the bridge assemblies with the round pocket toward the outside of the engine. Refer to Illustration 4.
Ensure that the crankshaft and the camshafts are in time with each other. Also ensure that the adjustment screws in the rocker arms are loosened completely before the bolts on the rocker shaft are tightened or damage to the valves and the pistons may occur.
If the rocker shaft is not positioned correctly, the oil supply to the sleeve bearings in the rocker arm will be shut off. This will cause seizure of the bearings and severe damage to the engine.Be sure to orient the rocker shaft in the correct position.
Place rocker shaft assembly (2) in position on valve mechanism cover base (6). Make sure that valve pushrods (4) and pushrod (5) are aligned with the rocker arms. Install bolts (1). Tighten the bolts evenly to a torque of 215 40 N m (160 30 lb ft).Note: The rocker shaft dowel must be located on the left-hand side of the rocker shaft when installed.
Illustration 5 g01119849
Adjust the valve lash according to Testing and Adjusting, "Valve Lash and Valve Bridge Adjustment". Hold adjustment screw (7) of the rocker arm assembly and tighten jam nut (8) to a torque of 70 15 N m (52 11 lb ft).
Adjust the electronic unit injector lash according to Testing and Adjusting, "Fuel Injector Adjustment". Hold adjustment screw (9) of the rocker arm assembly and tighten nut (10). If nut (10) is 5/8 inch thread,
Cat SIS web machinery list:
Parts washer Caterpillar catalog:
2470C, 2570C, 2670C, 2864C, 508, 533, 543, 553C, 563C, 573C, 586C, 735, 740, 814, 814F, 814F II, 815, 815B, 815F, 815F II, 816, 816B, 816F, 816F II, 924K, 930K, 936, 936F, 938F, 938G, 938G II, 950, 95...
924F, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, IT18F, IT24F, IT28F, IT28G
924G, 924GZ, 924H, 924HZ, 926, 926A, 928F, 928G, 928H, 928HZ, 930, 930G, 930R, IT28, IT28F, IT28G, SM-350
120G, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 924K, 928F, 928G, 928H, 928HZ, 930G, 930K, 938K, IT18F, IT24F, IT28F, IT28G
918F, 924F, 924G, 924GZ, 924H, 924HZ, 924K, IT12B, IT18F, IT24F
910E, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, IT12B, IT14B, IT14F, IT18F, IT24F, IT28G
515, 525, 924F, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 938F, 938G, 938G II, 950 GC, 950F II, 950G, 960F, IT28F, IT28G, IT38F, IT38G, IT38G II, R1300G, R1300G II
924G, 924GZ, 924H, 924HZ, 924K, 928G, 928H, 928HZ, 930G, 930K, 938K, FUSION, IT28G
924G, 924GZ, 924H, 924HZ, 924K, 928G, 928H, 928HZ, 930G, 930K, 938K, FUSION, IT28G
508, 518, 730, 730C, 950B, 950B/950E, D300D, D300E, D300E II, G936
735, 815B, 816B, 966D, D25C, D25D, D30C, D350C, D350E, D350E II, D35C, D35HP, D400
735, 815B, 816B, 966D, D25C, D25D, D30C, D350C, D350E, D350E II, D35C, D35HP, D400
3406C, 3412, 3412C, 3412E, 5110B, 651E, 657E, 7155, 773B, 775B, 988F, 990, 992C, 992D, D343, G3412, PM3412, PR-1000, PR-750B, SCT673, SPS342, SPT342
311, 311B, 312, 312B, 312B L, 312C L, 315, 315B L, 317, 317B LN, 318B, 325 L, 3406E, 3412, 3412C, 3412E, 3456, 613C, 613C II, 615, 621, 621B, 621E, 621F, 621G, 623B, 623E, 623F, 623G, 627B, 627E, 627F...
120, 120M, 120M 2, 12E, 12M, 12M 2, 12M 3, 12M 3 AWD, 140, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673B, 172, 215B, 225, 229, 229D, 235, 235B, 235C, 235D, 245, 245B, ...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H,...
3208, 3406, 3406B, 943, D5, D5B, D6C, D6D, G3306
225, 231D, 3208, 613B, 613C, CS-551, PR-1000, PS-500
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 950 GC, C15, C175-16, C32, G3508, G3512, G3512E, G3516, G3516B, G3516C, G3516E, G3516H, G3520B, G3520C, G3520E, PM3516, XQC1200
1140, 1160, 12F, 12G, 14E, 14G, 16, 1674, 1676, 16G, 225, 3160, 3176B, 3176C, 3196, 3406, 613, C-12, C12, D334, D348, G343, G3516, MP15, S305, VHS-50, VT50
3176B, 3176C, 3196, 3406B, 3406E, C-12, C-15, C12, C15, C18
3176B, 3176C, 3196, 3406B, 3406E, C-12, C-15, C12, C15, C18
3412, 814F, 814F II, 815F, 815F II, 816F, 816F II, 844, 844H, 854G, 854K, 918F, 924F, 928F, 938F, 950F II, 960F, 966F II, 970F, 990, 990 II, 990H, 992G, 992K, 994F, D10T, D10T2, D11T, IT18F, IT24F, IT...