AVSPARE.COM
parts catalog

WASHER 2F7826 - Caterpillar


2F7826 WASHER Caterpillar parts 561B, 561C, 977D, 977H, D337, D5, D5B, D5E
Rating:
20
Alternative (cross code) number:
CA2F7826
2F-7826
2F7826
Caterpillar 2F7826 WASHER
Weight: 0.38 pounds 0 kg.
Information:
MATERIAL THICKNESS  9.525  mm
NUMBER OF PITCH HOLES 
OD  58.725  mm
PITCH CIRCLE DIAMETER  23.813  mm
PITCH CIRCLE HOLE DIAMETER  13.494  mm

Buy WASHER 2F7826 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE, TRACK-TYPE TRACTOR,

Compatible equipment models: 2F7826:

MARINE ENGINE  D337  
PIPELAYER  561B   561C  
TRACK LOADER  977D   977H  
TRACK-TYPE TRACTOR  D5   D5B   D5E   Caterpillar
Number on catalog scheme: None
  For full view, you need register

Information:

9S8900 Cylinder5F9888 Adapter5F9892 Pin5P6514 Adapter5P6541 Sleeve5P316 Spanner Wrench6V6080 Torque Multiplier9S7352 Torque Wrench1. Heat race (3) for inner roller bearing in oil to a maximum temperature of 135°C (275°F) and install race on end of sprocket shaft (2).2. Use the tool set up and install inner bearing cone (1) on sprocket shaft (2) with a force of 98 to 240 kN (9 to 27 tons).3. Install gear (4) and bolts and nuts (5). Tighten nuts to a torque of 80 7 N m (60 5 lb.ft.). Then turn an additional 120° 5°. Torque after turning 120° 5° to be 305 N m (230 lb.ft.).4. Install bearing cup (8), spacer (9) and bearing cup (10) in housing (7).5. Put the sprocket shaft (2) in vertical position on blocks and install housing (7).6. Install spacer (6) on sprocket shaft (2).7. Use the tool set up and install outer bearing cone (11) on sprocket shaft (2) with a force of 178 to 240 kN (20 to 27 tons) while turning housing (7) to set bearing cone (11) in cup (10).8. Put oil on threads of sprocket shaft (2) and install nut (12) until the threads of sprocket shaft begin to show beyond the friction material of nut (12).9. Put 7M7260 Liquid Gasket on cover and case faces and install cover on case.10. Use the 5P316 Spanner Wrench and 9S7352 Torque Wrench and check the torque needed to turn nut (12). If same nut is used again, it must take at least 55 N m (40 lb.ft.) to turn nut. If not, use a new nut with oil on threads of nut and on friction material of nut. A new nut must take at least 80 N m (60 lb.ft.) to turn it. The torque needed to turn nut (12) is with clean threads, oil on the threads and friction material of nut and all of nut and friction material of nut engaged on threads of sprocket shaft but nut not making contact with bearing.11. Use 5P316 Spanner Wrench, 6V6080 Torque Multiplier and 9S7352 Torque Wrench and tighten nut (12) to a torque of 815 + 400 - 65 N m (600 + 300 - 50 lb.ft.).

Caterpillar parts catalog:

Caterpillar parts catalog
D337 MARINE ENGINE 23B00300-00455
561C PIPELAYER 92J00001-00390 (MACHINE)
D5 TRACTOR / DIRECT DRIVE / 93J00001-00731 (MACHINE)
D5 TRACTOR / DIRECT DRIVE / 93J00905-UP (MACHINE) POWERED BY 3306 ENGINE
561C PIPELAYER 92J00596-UP (MACHINE) POWERED BY 3306 ENGINE
D5B TRACTOR / DIRECT DRIVE / 22X00001-00438 (MACHINE) POWERED BY 3306 ENGINE
D5 TRACTOR / DIRECT DRIVE / 93J00905-UP (MACHINE) POWERED BY 3306 ENGINE
561C PIPELAYER 92J00596-UP (MACHINE) POWERED BY 3306 ENGINE
561C PIPELAYER 92J00001-00390 (MACHINE)
D5 TRACTOR / DIRECT DRIVE / 93J00001-00731 (MACHINE)
561C PIPELAYER 92J00391-UP (MACHINE)
561 PIPELAYER 62A00205-00387 (MACHINE)
D5E Track-Type Tractor 9RG00001-UP (MACHINE) POWERED BY 3306 Engine


Parts washer Caterpillar catalog:

9B8717 WASHER
955C, 977D, D315, D337, D342, D353C, D8H, D9E, G342C
1H7713 WASHER
641B, 650B, 651B, 666, 920, 930, 941, 955C, 977D, D337, D342, D9G, D9H
8F9320 WASHER
118, 583K, 594, 594H, 824B, 824S, 983, D337, D7F, D8H, D8K, D9G, D9H
5H1789 WASHER
12E, 16, 657, 955H, 977H, D326F, D337, D364
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.