WASHER 2S1418 - Caterpillar

Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed. The user is responsible for the performance of maintenance, including all adjustments, the use of proper lubricants, fluids, and filters. The user is also responsible for the replacement of components due to normal wear and aging. Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components. Use fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, to determine the maintenance intervals. Products that operate in severe operating conditions may require more frequent maintenance. Before each consecutive interval is performed, all maintenance from the previous interval must be performed.When Required
Air Inlet Filter - Inspect/Clean/Test
Air Starting Motor Lubricator Oil Level - Check
Battery - Replace
Belts - Inspect/Adjust/Replace
Engine Air Precleaner - Check/Clean
Engine Oil Level - Check
Generator - Dry
Generator Winding - Test
Rotating Rectifier - Inspect/Test
Varistor - Check
Daily
Fuel Filter Differential Pressure - Check
Generator Load - Check
Every Week
Air Inlet Filter - Inspect/Clean/Test
Air Starting Motor Lubricator Oil Level - Check
Air Tank Moisture and Sediment - Drain
Automatic Start/Stop - Inspect
Battery Charger - Check
Battery Electrolyte Level - Check
Control Panel - Inspect/Test
Coolant Level - Check
Electrical Connections - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Air Precleaner - Check/Clean
Engine Oil Level - Check
Fuel Filter Differential Pressure - Check
Generator - Inspect
Generator Bearing Temperature - Test/Record
Generator Load - Check
Generator Set - Test
Jacket Water Heater - Check
Power Factor - Check
Space Heater - Test
Standby Generator Set Maintenance Recommendations
Stator Winding Temperature - Test
Voltage and Frequency - Check
Walk-Around Inspection
Every 250 Service Hours
Coolant Sample (Level 1) - Obtain
Every 1000 Service Hours or 6 Weeks
Engine Crankcase Breather - Clean
Engine Oil Filter (Auxiliary) - Change
Every 4000 Service Hours
Engine Valve Lash - Check
Every Year
Actuator Control Linkage - Lubricate
Aftercooler Condensation - Drain
Air Starting Motor Lubricator Bowl - Clean
Alternator - Inspect
Belts - Inspect/Adjust/Replace
Carburetor Air/Fuel Ratio - Check/Adjust
Coolant Sample (Level 2) - Obtain
Coolant Temperature Regulator - Replace
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Crankcase Blowby - Test/Record
Crankshaft Vibration Damper - Inspect
Cylinder Pressure - Test/Record
Engine Air Cleaner Element (Single Element) - Inspect/Replace
Engine Crankcase Breather - Clean
Engine Mounts - Inspect
Engine Oil - Change
Engine Oil Filter (Auxiliary) - Change
Engine Oil Filter - Change
Engine Oil Level - Check
Engine Oil Sample - Obtain
Engine Performance - Test
Engine Protective Devices - Check
Engine Speed/Timing Sensor - Clean/Inspect
Engine Valve Lash - Check
Exhaust Bypass - Inspect
Exhaust Piping - Check
Gas Pressure Regulator Condensation - Drain
Generator Bearing - Lubricate
Generator Set Vibration - Inspect
Generator Winding Insulation - Test
Hoses and Clamps - Inspect/Replace
Ignition System Timing - Check/Adjust
Inlet Air System - Check
Radiator - Clean
Spark Plugs - Inspect/Adjust/Replace
Starting Motor - Inspect
Stator Lead - Check
Valve Stem Projection - Measure/Record
Water Pump - Inspect
Every 3 Years
Coolant (DEAC) - Change
Coolant (NGEC) - Change
Coolant Temperature Regulator - Replace
Rotating Rectifier - Check
Turbocharger - Inspect