2S3728 WASHER Caterpillar parts
227, 920, 930, 930R, HEX-WEDGE
Rating:
Alternative (cross code) number:
CA2S3728
2S-3728
2S3728
CA2S3728
2S-3728
2S3728
Weight: 0.80 pounds 0 kg.
Information:
ID
27
mm
MATERIAL
Steel
MATL THK
10.3
mm
OD
79
mm
LOGGER, WHEEL LOADER,
Compatible equipment models: 2S3728:
Number on catalog scheme:
For full view, you need register
Information:
Piston Pin Bearings
Note: This procedure requires personnel with the correct training and the use of specialized equipment for machining.If the piston pin bearing requires replacement but the original connecting rod is not replaced, the following procedures must be performed:
Remove the piston pin bearing from the connecting rod. Install a new bearing in the connecting rod. The new bearing is partially finished. The new bearing must be bored off-center to the correct diameter. This off-center position is determined by the length of the connecting rod. Refer to table 1. The correct diameter of the bore in the piston pin bearing is given in Specifications , "Connecting Rod". Surface finish of the bored hole in the piston pin bearing ... Ra 0.8 micrometers
Machine the ends of the piston pin bearing to the correct length. Remove any sharp edges. Refer to Specifications, "Connecting Rod". Table 1 references the following information: Grade of letter of the connecting rod, the color code of the connecting rod and the length of the connecting rod.
Table 1
Specifications for the Connecting Rod
Grade Letter Color Code Length Of The Connecting Rod (CRL)
B Blue 161.107 to 161.140 mm (6.3428 to 6.3441 inch)
Note: This procedure requires personnel with the correct training and the use of specialized equipment for machining.If the piston pin bearing requires replacement but the original connecting rod is not replaced, the following procedures must be performed:
Remove the piston pin bearing from the connecting rod. Install a new bearing in the connecting rod. The new bearing is partially finished. The new bearing must be bored off-center to the correct diameter. This off-center position is determined by the length of the connecting rod. Refer to table 1. The correct diameter of the bore in the piston pin bearing is given in Specifications , "Connecting Rod". Surface finish of the bored hole in the piston pin bearing ... Ra 0.8 micrometers
Machine the ends of the piston pin bearing to the correct length. Remove any sharp edges. Refer to Specifications, "Connecting Rod". Table 1 references the following information: Grade of letter of the connecting rod, the color code of the connecting rod and the length of the connecting rod.
Table 1
Specifications for the Connecting Rod
Grade Letter Color Code Length Of The Connecting Rod (CRL)
B Blue 161.107 to 161.140 mm (6.3428 to 6.3441 inch)
Caterpillar parts catalog:
Parts washer Caterpillar catalog:
518, 910, 930, 930R, IT12
518, 910, 930, 930R, IT12
916, 920, 926, G916, IT18B, IT28
924G, 924GZ, 924H, 924HZ, 926, 926A, 928F, 928G, 928H, 928HZ, 930, 930G, 930R, IT28, IT28F, IT28G, SM-350
916, 918F, 920, 924F, IT18B, IT18F, IT24F
518, 910, 930, 930R
518, 930, 930R
518, 930, 930R
613, 613B, 920, 950, 966C, 966R
920
508, 518, 910, 916, 920, 926, G926, IT28
518, 930, 930R
8S2684
WASHER
773, 992
773, 992
8S2685
WASHER
773, 992
773, 992
518, 930, 930R
518, 930, 930R
930
6K6184
WASHER
930
930
621, 621B, 621R, 623, 623B, 627B, 631C, 633C, 641B, 650B, 657, 657B, 666, 666B
5D0081
WASHER
641B, 651
641B, 651
7J2600
WASHER
641B, 657B
641B, 657B
3D8511
WASHER
641, 650B, 651, 657, 657B, 666, 772, 773
641, 650B, 651, 657, 657B, 666, 772, 773
3K5599
WASHER
641B, 650B, 657B, 666
641B, 650B, 657B, 666
4D0821
WASHER
621, 623, 627, 641, 641B, 651, 657, 657B
621, 623, 627, 641, 641B, 651, 657, 657B