WASHER 4253355 - Caterpillar

4253355 WASHER Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4253355
425-3355
4253355

Weight: 4 pounds 1 kg.

Buy WASHER 4253355 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

05 May 2025
0.01[0.00] pounds
Amazon.com

Hacus - Forklift FPE378049 O-Ring Hacus Aftermarket - New
Hacus HIGH-QUALITY CONSTRUCTION: Made with premium materials; built to withstand the demands of industrial environments; offering excellent resistance to wear; corrosion; and mechanical stress. || VERSATILE COMPATIBILITY: Engineered to fit a wide range of forklift models; making it a versatile choice for various equipment configurations. || SAFETY FIRST - FPE products are ready for use with all certifications. || LEADING THE INDUSTRY - FPE is a leader in forklift products and accessories. We take pride in making the highest quality, premium, reliable forklifts on the market. || All products tested for durability, reliability, and performance.

15 Nov 2024
0.01[0.00] pounds
Amazon.com

Hacus - Forklift FPE378049 O-RING Hacus Aftermarket - New
Hacus HIGH-QUALITY CONSTRUCTION: Made with premium materials; built to withstand the demands of industrial environments; offering excellent resistance to wear; corrosion; and mechanical stress. || VERSATILE COMPATIBILITY: Engineered to fit a wide range of forklift models; making it a versatile choice for various equipment configurations. || SAFETY FIRST - FPE products are ready for use with all certifications. || LEADING THE INDUSTRY - FPE is a leader in forklift products and accessories. We take pride in making the highest quality, premium, reliable forklifts on the market. || All products tested for durability, reliability, and performance.

This part in 1 request: Show. This information for suppliers only!

#1074727 4253355

2023-03-09

Number on catalog scheme: 13

For full view, you need register

Information:

Illustration 1 g02351777
Schematic for the Right Hand Joystick Control sensorNote: The sensor is not directly connected to the frame ground. The sensor return connects to the ECM, and the ECM connects the sensor return to frame ground internally.This diagnostic code is for the Right Hand Joystick Control sensor for left and right motion. An FMI 04 indicates the machine ECM has determined the sensor output signal voltage is below normal. Possible causes for this diagnostic code are:
A failed sensor.
The sensor output signal is shorted to ground.
The machine ECM may have failed, but is unlikely.Note: Poor connections are often the cause of a problem in electrical circuits. Before performing this procedure, inspect all the machine harnesses and connectors involved in the circuit. Make sure to verify that all of the connections in the circuit are clean, secure, and in good condition. Correct any problems found with any of the connections. Verify the diagnostic code CID 1128 FMI 04 is still active, before continuing with this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes now, but clear those codes when the original diagnostic code has been corrected. Test Step 1. CHECK THE SENSOR
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness connector from the Right Hand Joystick Control sensor.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the CID 1128 FMI 04 diagnostic code. Expected Result:The CID 1128 FMI 04 code stays active. Results:
YES - The CID 1128 FMI 04 code stays active. The sensor is not the problem. Go to Test Step 2.
NO - The CID 1128 FMI 04 code is no longer active and has been replaced by an active CID 1128 FMI 03code. The sensor has failed. Repair: Replace the sensor. The new sensor will need to be calibrated. Go to Test Step 3.Test Step 2. CHECK THE SENSOR CIRCUIT FOR A SHORT.
Turn the key start switch and the disconnect switch to the OFF position.
The sensor harness connector stays disconnected.
Disconnect both the J1 and J2 machine harness connectors from the machine ECM.
At the ECM harness connectors, measure the resistance from the contact J1-2 (wire M962-YL) to all of the other contacts that are used in both the J1 and J2 ECM harness connectors. Expected Result:Each resistance measured is more than 5000 ohms. Results:
YES - Each resistance measured is more than 5000 ohms. The machine harness is correct. Go to Test Step 3.
NO - A resistance measured is not more than 5000 ohms. There is a short in the machine harness. The short is between J1-2 (wire M962-YL) and the circuit with the low resistance.Repair: Repair or replace the harness. Go to Test Step 3.Test Step 3. CHECK THE DIAGNOSTIC CODE STATUS.
Reconnect all harness connectors. Make sure that the connectors are fully seated. Observe that the clips on each connector are securely fastened.
Turn the disconnect switch and the key start switch to the ON position.
Clear all inactive