7F0502 WASHER Caterpillar parts
12E, 153, 163, 173B, 183B, 225, 4S, 528, 561B, 571G, 572G, 578, 583K, 583R, 589, 594, 594H, 613, 613B, 613C, 615, 615C, 621, 621B, 627B, 630B, 641, 641B, 650B, 651, 651B, 657, 657B, 666, 666B, 769, 77...
Rating:
Alternative (cross code) number:
CA7F0502
7F-0502
7F0502
CA7F0502
7F-0502
7F0502
Weight: 0.04 pounds 0 kg.
Information:
ID
13.5
mm
MATERIAL
Steel
MATL THK
3
mm
OD
31.8
mm
BULLDOZER, WHEEL TRACTOR,
Compatible equipment models: 7F0502:
Number on catalog scheme:
1
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
Clean and polish the crankshaft of imperfections.
Use Tooling (A) to clean the outside diameter of the crankshaft and the inside diameter of the crankshaft wear sleeve.
Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of the crankshaft wear sleeve.
Use Tooling (C) to install the crankshaft wear sleeve. Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft rear seal must be installed dry.Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these components should not be used.
Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal (1).
Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push crankshaft rear seal (1) in place to dislodge the shipping sleeve. Note: Do not remove the shipping sleeve until bolts (2) are installed.
Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in Illustration 2. Tighten bolts (2) to a torque of 12 3 N m (106 27 lb in). End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
Clean and polish the crankshaft of imperfections.
Use Tooling (A) to clean the outside diameter of the crankshaft and the inside diameter of the crankshaft wear sleeve.
Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of the crankshaft wear sleeve.
Use Tooling (C) to install the crankshaft wear sleeve. Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft rear seal must be installed dry.Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these components should not be used.
Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal (1).
Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push crankshaft rear seal (1) in place to dislodge the shipping sleeve. Note: Do not remove the shipping sleeve until bolts (2) are installed.
Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in Illustration 2. Tighten bolts (2) to a torque of 12 3 N m (106 27 lb in). End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Cat SIS web machinery list:
Parts washer Caterpillar catalog:
69D, 769, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772B, 772G, 772G OEM, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 775B, 775D, 775E, 775F, 775G, 775G LRC, AD30, AD40, AD45, AD45B, AD55, AD...
824C, 825C, 826C, D7G
120, 120B, 120G, 120H, 120K, 120K 2, 12E, 12F, 12G, 12H, 130G, 135H, 140, 140B, 140G, 140H, 140K, 14E, 160G, 160H, 160K
120B, 12E, 12F, 140, 140B, 14E
120, 120B, 12E, 140, 140B
120B, 12E, 140, 140B
120, 120B, 12E, 12F, 140, 140B, 14E
120B, 12E, 12F, 140B, 14E
120, 120B, 12E, 140, 140B, 14E
120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
12E
120B, 140B, 225, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 8A, 8S, 931, 941, 943, 951B, 953, D5B, D6D
7J3957
WASHER
225, 229, 772, 773, 776C, AD30
225, 229, 772, 773, 776C, AD30
7J0699
WASHER
16, 225, 572G, 631C
16, 225, 572G, 631C
8K0319
WASHER
215B, 225, 227, 229, FB221
215B, 225, 227, 229, FB221
120, 120G, 12G, 130G, 140, 140G, 14E, 14G, 16, 16G, 215, 225, 235, 245, 630B, 651, 657, 824, 834, 988B, 994, D8H, D8K, D9H
9H7084
WASHER (plain)
118, 172, 225, 571G, 630B, 633, 651B, 657, 657B, 666, 769, 910, 977K, 977L, 983B, 992, D4E, D6D
118, 172, 225, 571G, 630B, 633, 651B, 657, 657B, 666, 769, 910, 977K, 977L, 983B, 992, D4E, D6D
571G, 583K, 941, 950, 977K, D4D, D7G, D8H, D8K
120G, 12G, 130G, 140G, 14G, 16G, 627, 931B, 931C, 931C II, 935C, 941, 955K, 955L, 963, D350E, D350E II, D3C, D3C II, D400E, D400E II, D4B, D4C, D4C II, D4D, D4H, D4H XL, D5C, D5C III, D5H, D5H XL, D5H...
3K7628
WASHER ASSEM.
215, 225, 235, 245, 824B, 950, 966C, 988
215, 225, 235, 245, 824B, 950, 966C, 988
4D7464
WASHER
120, 120G, 12E, 140, 14E, 225, 235, 245, 631C, 641, 651, 825B, 943, 953, 963, 966C, 980, 988, 992, AD40, AD45, AE40, D10, D4E, D5, D5B, D6C, D6D, D7G, D8H, D8K, D9G, D9H
120, 120G, 12E, 140, 14E, 225, 235, 245, 631C, 641, 651, 825B, 943, 953, 963, 966C, 980, 988, 992, AD40, AD45, AE40, D10, D4E, D5, D5B, D6C, D6D, D7G, D8H, D8K, D9G, D9H
5D1245
WASHER
120B, 12E, 140, 140B, 14E, 215, 225, 235, 245, 621B, 627B
120B, 12E, 140, 140B, 14E, 215, 225, 235, 245, 621B, 627B
0L2112
WASHER
225
225