WASHER-HARD 7X0533 - Caterpillar

Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed.The user is responsible for the performance of maintenance, including all adjustments, the use of proper lubricants, fluids, filters, and the replacement of components due to normal wear and aging. Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components.Use mileage, fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, to determine the maintenance intervals. Products that operate in severe operating conditions may require more frequent maintenance.Note: Before each consecutive interval is performed, all maintenance from the previous interval must be performed.When Required
Battery - Replace
Battery or Battery Cable - Disconnect
Engine - Clean
Engine Oil Level Gauge - Calibrate
Engine Storage Procedure - Check
Fuel System - Prime
Heat Exchanger - Inspect
Maintenance Recommendations
Sea Water Strainer - Clean/Inspect
Zinc Rods - Inspect/Replace
Daily
Cooling System Coolant Level - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Oil Level - Check
Fuel System Primary Filter/Water Separator - Drain
Walk-Around Inspection
Initial 10 Service Hours
Belts - Inspect/Adjust/Replace
Every 50 Service Hours or Weekly
Sea Water Strainer - Clean/Inspect
Zinc Rods - Inspect/Replace
First 22 700 L (6000 US gal) of Fuel or 250 Service Hours
Engine Valve Lash - Inspect/Adjust
Initial 500 Hours (for New Systems, Refilled Systems, and Converted Systems)
Cooling System Coolant Sample (Level 2) - Obtain
Every Year
Cooling System Coolant Sample (Level 2) - Obtain
Every 22 700 L (6000 US gal) of Fuel or 250 Service Hours or 1 Year
Auxiliary Water Pump (Rubber Impeller) - Inspect
Battery Electrolyte Level - Check
Belts - Inspect/Adjust/Replace
Cooling System Coolant Sample (Level 1) - Obtain
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Engine - Clean
Engine Air Cleaner Element - Clean/Replace
Engine Crankcase Breather - Clean
Engine Oil Sample - Obtain
Engine Oil and Filter - Change
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Fuel Tank Water and Sediment - Drain
Hoses and Clamps - Inspect/Replace
Every 90 850 L (24 000 US gal) of Fuel or 1000 Service Hours
Closed Crankcase Ventilation (CCV) Fumes Disposal Filter - Replace
Turbocharger - Inspect
Every 272 550 L (72 000 US gal) of Fuel or 3000 Service Hours
Auxiliary Water Pump (Bronze Impeller) - Inspect
Cooling System Coolant (DEAC) - Change
Cooling System Water Temperature Regulator - Replace
Crankshaft Vibration Damper - Inspect
Engine Mounts - Inspect
Engine Speed/Timing Sensors - Check/Clean/Calibrate
Engine Valve Lash - Inspect/Adjust
Engine Valve Rotators - Inspect
Heat Exchanger - Inspect
Starting Motor - Inspect
Every 454 250 L (120 000 US gal) of Fuel or 5000 Service Hours
Alternator - Inspect
Maintenance Recommendations
Oil Cooler Core - Check/Clean/Test
Overhaul (Top End)
Water Pump - Inspect
Every 3000 Service Hours or 2 Years
Aftercooler Core - Clean/Test
Every 6000 Service Hours or 3 Years
Cooling System Coolant Extender (ELC) - Add
Every 12 000 Service Hours or 6 Years
Cooling System Coolant (ELC) - Change
Every 6 Years
Aftercooler Core - Replace
Overhaul
Maintenance Recommendations
Overhaul (Major)