6V6384 WATER PUMP Caterpillar parts
D398, D399
Rating:
Alternative (cross code) number:
CA6V6384
6V-6384
6V6384
CA6V6384
6V-6384
6V6384
Weight: 3 pounds 1 kg.
INDUSTRIAL ENGINE,
Related part:
6V6384
GASKET KT-WTR-YM
3872917
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$120.81
15 Aug 2019
600 Hundredths Pounds
CTP: CTP
6V6384 Kit Gasket Fits Caterpillar D398 D398B D399
Warranty
Warranty
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 0V-0375 Bolt 1
5P-8245 Hard Washer 1 Start By:
Install the lifting brackets on the engine. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00921920Note: Mark the positions of supports (4) and shims (5). The engine supports on the right side are attached to plates (6) on the generator base by dowels (1). Dowels (1) must be removed before the mounting supports can be removed.
Use Tooling (A) to remove dowels (1).
Attach a suitable lifting device to the lifting brackets. The weight of the six cylinder engine is approximately 15 650 kg (34,500 lb). The weight of the eight cylinder engine is approximately 20 412 kg (45,000 lb). Note: The weight is ONLY for the engine.
Loosen bolt (2).
Remove bolts (3) that hold the engine supports to the base.
Lift the engine enough in order to place a nylon strap around the support. The weight of each support is approximately 64 kg (141 lb).
Illustration 2 g00921919
Remove bolts (8) that hold the support (4) to the cylinder block.
Tap support (4) with a large plastic hammer in order to disengage dowels (7) from the cylinder block.
Remove support (4) from the side of the cylinder block.
If necessary, remove dowels (7) from engine support (4). Installation Procedure
Illustration 3 g00921919
If dowels (7) were removed from support (4), install dowels (7). Dowels (7) should extend 20.0 1.0 mm (0.79 0.04 inch) above the surface of support (4).
Put the support in the correct position on the cylinder block. Install the bolts (8). Tighten the bolts to a torque of 1125 100 N m (830 75 lb ft).
Illustration 4 g00921920
Install shims (5) in the regular location.
Lower the engine onto plates (6). Install bolts (3).
Install dowels (1) through engine support (4) and into plate (6) on the right side of the engine.
Check the alignment between the engine and the driven equipment. End By:
Remove the lifting brackets from the engine. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 0V-0375 Bolt 1
5P-8245 Hard Washer 1 Start By:
Install the lifting brackets on the engine. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00921920Note: Mark the positions of supports (4) and shims (5). The engine supports on the right side are attached to plates (6) on the generator base by dowels (1). Dowels (1) must be removed before the mounting supports can be removed.
Use Tooling (A) to remove dowels (1).
Attach a suitable lifting device to the lifting brackets. The weight of the six cylinder engine is approximately 15 650 kg (34,500 lb). The weight of the eight cylinder engine is approximately 20 412 kg (45,000 lb). Note: The weight is ONLY for the engine.
Loosen bolt (2).
Remove bolts (3) that hold the engine supports to the base.
Lift the engine enough in order to place a nylon strap around the support. The weight of each support is approximately 64 kg (141 lb).
Illustration 2 g00921919
Remove bolts (8) that hold the support (4) to the cylinder block.
Tap support (4) with a large plastic hammer in order to disengage dowels (7) from the cylinder block.
Remove support (4) from the side of the cylinder block.
If necessary, remove dowels (7) from engine support (4). Installation Procedure
Illustration 3 g00921919
If dowels (7) were removed from support (4), install dowels (7). Dowels (7) should extend 20.0 1.0 mm (0.79 0.04 inch) above the surface of support (4).
Put the support in the correct position on the cylinder block. Install the bolts (8). Tighten the bolts to a torque of 1125 100 N m (830 75 lb ft).
Illustration 4 g00921920
Install shims (5) in the regular location.
Lower the engine onto plates (6). Install bolts (3).
Install dowels (1) through engine support (4) and into plate (6) on the right side of the engine.
Check the alignment between the engine and the driven equipment. End By:
Remove the lifting brackets from the engine. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Caterpillar parts catalog:
Parts water Caterpillar catalog:
2L1630
WATER PUMP GROUP
D375D, D379, D397D, D398, G379, G398
D375D, D379, D397D, D398, G379, G398
6L2601
WATER LINES GROUP
D379, D398, G379, G398
D379, D398, G379, G398
6L9902
WATER LINES
D399, G399
D399, G399
7L0591
WATER SHIELDED MANIFOLDS
D398, D398A
D398, D398A
2N6365
WATER COOLED
D398, D398A
D398, D398A
D379, D379A, D398, D398A, G379, G398
D379, D398
D379B, D398B, D399
D379, D398
1P6303
WATER PUMP AFTERCOOLER
D346, D348, D349
D346, D348, D349
641B, 650B, 657B, 666B, 772, 773, D346, D349, D4H, D4HTSK II
641B, 650B, 657B, 666B, 772, 773, 992, D346, D348, D349
641B, 650B, 777, 992
7S1221
WATER PUMP REBUILD KIT
641B, 650B, 772, 992
641B, 650B, 772, 992
1P6302
WATER PUMP REBUILD KIT
777, D346
777, D346
D343, G343
D379B, D398B, D399