4P7692 WEIGHT-GOVERNOR Caterpillar parts
245D, 3406B, 980F
Rating:
Alternative (cross code) number:
CA4P7692
4P-7692
4P7692
CA4P7692
4P-7692
4P7692
Weight: 0.09 pounds 0 kg.
EXCAVATOR, WHEEL LOADER,
This part in 2 request:
Show.
This information for suppliers only!
2021-06-16
2019-10-29
Compatible equipment models: 4P7692:
Information:
Remove Pistons
start by: a) remove cylinder headsb) remove oil pan1. Remove the ring of carbon from the top inner surface of the cylinders with tool (A).2. Turn the crankshaft until two pistons are at bottom center. 3. Remove connecting rod caps (1) from the two connecting rods.
Do not let the connecting rods hit the bottom edge of the cylinder bores or the crankshaft during removal and installation of the pistons.
4. Push the piston and connecting rod away from the crankshaft until the piston rings are above the cylinder block. 5. Remove the two pistons (2) and the connecting rods. Keep each connecting rod cap with its respective connecting rod and piston. Put identification on each connecting rod as to its location for use at installation.6. Do Steps 3 through 6 for the remainder of the pistons.Install Pistons
1. Turn the crankshaft until the bearing journal for the pistons to be installed is at bottom center.2. Put clean engine oil on the crankshaft bearing journal and inside of the cylinder walls. Put clean engine oil on the piston rings and connecting rod bearings. 3. Make sure the ring gaps are approximately 120° apart. Install tool (A) on the piston.4. Put the piston in position in the same cylinder bore from which it was removed. The hole (crater) in the top of the piston must be toward (nearest) the center of the engine.5. Push the piston into place while putting the connecting rod into position on the crankshaft.6. Put clean engine oil on the threads of the bolts and contact surfaces of the nuts for the connecting rod caps.
When installing connecting rod caps, make sure that the numbers on the side of the cap is next to and respective with the number on the side of the connecting rod.
7. Put the cap in position on the connecting rod and install the nuts. Tighten the nuts to a torque of 30 3 lb. ft. (40.8 4.1 N m). Put a mark on each nut and the end of each bolt. Tighten the nuts 60 5° more.8. Follow the same above procedure for installation of the remainder of the pistons. end by: a) install cylinder headsb) install oil panDisassemble Pistons
start by: a) remove pistons 1. Remove the rings from the piston with tool (A). 2. Remove snap ring (2), pin (1), and connecting rod (3) from the piston.Assemble Pistons
1. Install connecting rod (1) in the piston with boss (2) on the same side as the hole (crater) in the top of the piston.2. Install piston pin (3) and snap ring (4). 3. When old pistons are to be used, clean the piston grooves with tool (A).4. Install the spring for the oil ring. Install the oil ring with tool (B). The gap in the ring must be approximately 180° from the oil ring spring connection.5. Install the compression ring using tool (B). The side of the ring having identification "TOP" must be toward top of piston. The gaps in the
start by: a) remove cylinder headsb) remove oil pan1. Remove the ring of carbon from the top inner surface of the cylinders with tool (A).2. Turn the crankshaft until two pistons are at bottom center. 3. Remove connecting rod caps (1) from the two connecting rods.
Do not let the connecting rods hit the bottom edge of the cylinder bores or the crankshaft during removal and installation of the pistons.
4. Push the piston and connecting rod away from the crankshaft until the piston rings are above the cylinder block. 5. Remove the two pistons (2) and the connecting rods. Keep each connecting rod cap with its respective connecting rod and piston. Put identification on each connecting rod as to its location for use at installation.6. Do Steps 3 through 6 for the remainder of the pistons.Install Pistons
1. Turn the crankshaft until the bearing journal for the pistons to be installed is at bottom center.2. Put clean engine oil on the crankshaft bearing journal and inside of the cylinder walls. Put clean engine oil on the piston rings and connecting rod bearings. 3. Make sure the ring gaps are approximately 120° apart. Install tool (A) on the piston.4. Put the piston in position in the same cylinder bore from which it was removed. The hole (crater) in the top of the piston must be toward (nearest) the center of the engine.5. Push the piston into place while putting the connecting rod into position on the crankshaft.6. Put clean engine oil on the threads of the bolts and contact surfaces of the nuts for the connecting rod caps.
When installing connecting rod caps, make sure that the numbers on the side of the cap is next to and respective with the number on the side of the connecting rod.
7. Put the cap in position on the connecting rod and install the nuts. Tighten the nuts to a torque of 30 3 lb. ft. (40.8 4.1 N m). Put a mark on each nut and the end of each bolt. Tighten the nuts 60 5° more.8. Follow the same above procedure for installation of the remainder of the pistons. end by: a) install cylinder headsb) install oil panDisassemble Pistons
start by: a) remove pistons 1. Remove the rings from the piston with tool (A). 2. Remove snap ring (2), pin (1), and connecting rod (3) from the piston.Assemble Pistons
1. Install connecting rod (1) in the piston with boss (2) on the same side as the hole (crater) in the top of the piston.2. Install piston pin (3) and snap ring (4). 3. When old pistons are to be used, clean the piston grooves with tool (A).4. Install the spring for the oil ring. Install the oil ring with tool (B). The gap in the ring must be approximately 180° from the oil ring spring connection.5. Install the compression ring using tool (B). The side of the ring having identification "TOP" must be toward top of piston. The gaps in the
Caterpillar parts catalog:
Parts weight Caterpillar catalog:
7N7264
WEIGHT-GOVERNOR
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 215, 225, 235, 235B, 245, 3204, 330, 330 FM L, 330 L, 3304, 3...
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 215, 225, 235, 235B, 245, 3204, 330, 330 FM L, 330 L, 3304, 3...
1192130
WEIGHT-GOVERNOR
245D, 3406B, 3406C, 375, 375 L, 5080, 587R, 621F, 623E, 623F, 627B, 627F, 814B, 980F, 980F II, D350E, D400, D400E, RM-250C, RR-250B
245D, 3406B, 3406C, 375, 375 L, 5080, 587R, 621F, 623E, 623F, 627B, 627F, 814B, 980F, 980F II, D350E, D400, D400E, RM-250C, RR-250B
1198699
WEIGHT-GOVERNOR
16G, 16H NA, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980F, 980G, D350E, D400, D400E, D8N, D8R, D8R II, HT40...
16G, 16H NA, 3406B, 3406C, 375, 375 L, 5080, 578, 583R, 587R, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 814B, 824C, 824G, 825G, 826C, 826G, 980C, 980F, 980G, D350E, D400, D400E, D8N, D8R, D8R II, HT40...
4P1634
WEIGHT-GOVERNOR
3406B, 578, 621E, 623E, 627E, 980F
3406B, 578, 621E, 623E, 627E, 980F
4P1634
WEIGHT-GOVERNOR
3406B, 578, 621E, 623E, 627E, 980F
3406B, 578, 621E, 623E, 627E, 980F
9Y7872
WEIGHT
3176
3176
5N1871
WEIGHT - 19.1 GRAMS (.674 OZ.)
3408, 993K, D3C II, R1300, R1300G, R1300G II
3408, 993K, D3C II, R1300, R1300G, R1300G II
5N1870
WEIGHT - 34.0 GRAMS (1.20 OZ.)
3306C, 3408, 980F, 980F II
3306C, 3408, 980F, 980F II
9L4990
WEIGHT ASSEM.
1674, 1693, 215, 3406, 621, 621B, 910, 931B, 943, 953
1674, 1693, 215, 3406, 621, 621B, 910, 931B, 943, 953
9L9676
WEIGHT ASSEM.
1140, 1160, 225, 3160, 613
1140, 1160, 225, 3160, 613
9L9352
WEIGHT ASSEM.
1160
1160
9L9388
WEIGHT AND LEVER GROUP
1150, 1160
1150, 1160
2768814
WEIGHT-INERTIA
G3516, G3516B, G3520B
G3516, G3516B, G3520B
7W8165
WEIGHT-BALANCER
3606, 3608, 3612, 3616
3606, 3608, 3612, 3616