AVSPARE.COM
parts catalog

WHEEL 0005243 - Caterpillar



0005243 WHEEL Caterpillar parts WHEEL
Rating:
61
Alternative (cross code) number:
CA0005243
000-5243
0005243
Caterpillar 0005243 WHEEL
Weight: 2 pounds 0 kg.

Buy WHEEL 0005243 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Table 1
    Air Compressors    
    TF-550     TF-750    
Caterpillar Part Numbers     4P-5435     185-5145    
143-9185 164-7557    
178-9497 164-7563    
125-9562 4P-2792    
167-1288 164-7559    
149-4915 164-7566    
131-6679 164-7560    
185-5140 164-7567    
144-2906 164-7564    
109-1317 160-9845    
117-0070 164-7561    
113-7665 109-1318    
145-0840 144-2907    The "Tu-Flo 550" air compressor and the "Tu-Flo 750" air compressor should not be replaced when the air compressors experience an excessive oil leak at the cylinder head gasket. Refer to table 1 for the corresponding Caterpillar part numbers of the air compressors. 4P-3977 Cylinder Head Gasket should be used to repair the excessive oil leaks at the cylinder head gasket. This kit should only be used to repair excessive oil leaks that occur at the cylinder head gasket.
Illustration 1 g01018314
Illustration 2 g01018330
The following procedure can be used to evaluate an oil leak at the cylinder head.
Determine if the oil leak is excessive.
An excessive oil leak (1) has oil that drips to the label. Also, an excessive oil leak (1) might have oil that drips to the ground. Refer to Illustration 1.
A small amount of oil can seep from the cylinder head during normal operating conditions (2). Refer to Illustration 2.Note: If the oil leak is not excessive, do not change the gasket. The air compressor is still functional. Wash the air compressor periodically and monitor the air compressor periodically.
Verify that the oil leak originates at the air compressor. If the oil leak does not originate at the air compressor, discontinue this procedure and perform the necessary repairs in order to eliminate the source of the leak. If the oil leak originates at the cylinder head gasket on the air compressor, proceed to Step 3.
Take a photograph of the oil leak for later reference.
Remove the cylinder head and clean the gasket surfaces. Scrape the soft carbon from the cylinder head surface before installation.
Replace the gasket by following the instructions and torque procedures that are included with the 4P-3977 Cylinder Head Gasket .Note: In the "part causing failure field", enter the 4P-3977 Cylinder Head Gasket. Record the serial number of the air compressor in the "claim story".In order to ensure warranty replacement, the part number of the compressor and the serial number of the compressor must be included in the "claim story". Also, be sure to photograph the compressor for later reference. This revised repair procedure is the required method for repairing a cylinder head gasket leak on the "Tu-Flo 550" air compressor and the "Tu-Flo 750" air compressor. The entire air compressor should not be replaced in order to repair an excessive leak in the head gasket.


Parts wheel Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.