AVSPARE.COM
parts catalog

WHEEL & TIRE GP 2389680 - Caterpillar



2389680 WHEEL & TIRE GP Caterpillar parts 416D, 420D, 428D, 432D, 442D WHEEL
Rating:
57
Alternative (cross code) number:
CA2389680
238-9680
2389680
Caterpillar 2389680 WHEEL & TIRE GP

Buy WHEEL & TIRE GP 2389680 Caterpillar genuine, new aftermarket tractor parts with delivery
BACKHOE LOADER,

Compatible equipment models: 2389680:

BACKHOE LOADER  416D   420D   428D   432D   442D   Caterpillar
  For full view, you need register

Information:


Illustration 5 g01389161
Terminals at the customer connector that are associated with the auxiliary pressure sensor
(14) Sensor supply
(15) Sensor return
(33) Auxiliary pressure (if equipped)
Illustration 6 g01159881
Terminal locations at the sensor connector
(Terminal A) Sensor supply
(Terminal B) Sensor return
(Terminal C) Signal
The connection of any electrical equipment and the disconnection of any electrical equipment may cause an explosion hazard which may result in injury or death. Do not connect any electrical equipment or disconnect any electrical equipment in an explosive atmosphere.
Test Step 1. Determine if the Code is Logged or Active
Connect Cat ET to the service tool connector.
Restore electrical power to the engine ECM.
Monitor the active diagnostic code and the logged diagnostic codes on Cat ET. Note: Wait at least 30 seconds in order for diagnostic codes to become active.Identify the diagnostic code.Results:
Logged code - Repair: Do not troubleshoot a logged code unless the code relates to an operator complaint. If the code is logged and the code does not relate to an operator complaint, clear the code.If the code is logged and the code relates to an operator complaint, check the integrity of the connections at the connectors.STOP
Active code - Proceed to Test Step 2.Test Step 2. Check the Supply Voltage at the Sensor ConnectorMeasure the voltage between terminal A (sensor supply) and terminal B (sensor return) at the harness connector for the sensor that relates to the code.Expected Result:The voltage is between 4.5 VDC and 5.5 VDC.Results:
OK - The voltage is between 4.5 VDC and 5.5 VDC. The supply voltage is at the sensor connector. Record the voltage measurement. If you are troubleshooting a -3 diagnostic code, proceed to Test Step 3. If you are troubleshooting a -4 diagnostic code, proceed to Test Step 6.
Not OK - The voltage is less than 4.5 VDC or the voltage is greater than 5.5 VDC.Repair: The voltage of the sensor supply is incorrect. Refer to Troubleshooting, "Sensor Supply - Test".STOPTest Step 3. Check for Battery Voltage on the Signal WireMeasure the voltage between the signal terminal and the return terminal on the harness connector for the sensor that relates to the diagnostic code.Expected Result:The voltage measurement is less than the +Battery voltage.Results:
OK - The voltage measurement is less than the +Battery voltage. The signal wire is not shorted to the +Battery. Proceed to Test Step 4.
Not OK - The voltage measurement is approximately equal to the +Battery voltage. The signal wire is shorted to the +Battery.Repair: Repair the wiring, when possible. Replace parts, if necessary. Verify that the problem is resolved.STOPTest Step 4. Check the Signal Wire for an Open Circuit
Disconnect the sensor that relates to the diagnostic code.
Connect a jumper wire between the signal terminal and the return terminal on the harness connector for the sensor that relates to the diagnostic code. This will replace the sensor with a short circuit.
Look for a -4 diagnostic code. Expected Result:The -3 code does not change to a -4 code

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine
432D Backhoe Loader BLD01595-03844 (MACHINE) POWERED BY 3054 Engine
416D Backhoe Loader BGJ00523-01315 (MACHINE) POWERED BY 3054 Engine
420D Backhoe Loader BKC00502-UP (MACHINE) POWERED BY 3054 Engine
420D Backhoe Loader BMC00611-UP (MACHINE) POWERED BY 3054 Engine
442D Backhoe Loader SMJ00001-UP (MACHINE) POWERED BY 3054C Engine
428D Backhoe Loader BXC00001-UP (MACHINE) POWERED BY 3054C Engine
428D Backhoe Loader MBM00001-UP (MACHINE) POWERED BY 3054C Engine
432D Backhoe Loader TDR00001-UP (MACHINE) POWERED BY 3054C Engine


Parts wheel Caterpillar catalog:

2678358 WHEEL & TIRE GP
416D, 420D, 424D, 428D, 432D, 442D
1197773 WHEEL & TIRE GP
416C, 416D, 420D, 424D, 428C, 428D, 432D, 442D
1124411 WHEEL AS
416, 416B, 416C, 416D, 420D, 426C, 428, 428B, 428D, 430D, 436C, 438C
9R0315 WHEEL AS
416B, 416C, 416D, 420D, 426, 426C, 428, 428B, 428C, 430D, 436C, 438C
1350770 WHEEL AS
416, 416B, 416C, 420D, 426B, 426C, 428B, 428C, 428D, 432D, 436C, 438C, 438D, 442D
1350786 WHEEL AS
416C, 416D, 420D, 424D, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
2713042 WHEEL AS
416C, 416D, 420D, 424D, 428C, 428D, 430D, 432D, 438C, 438D, 442D
2713050 WHEEL AS
416D, 420D, 424D, 428C, 428D, 432D, 438D, 442D
2026186 WHEEL AS
414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 442D, 442E
1595761 WHEEL & TIRE AR
216, 236, 236B, 242B, 242B3, 246C, 248, 252B, 252B3, 256C, 262C, 268B, 272C
3196517 WHEEL & TIRE AR
120M, 12M, 140M, 160M
2520686 WHEEL & TIRE GP
120M, 12M, 140M, 160M
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.