2692560 WHEEL & TIRE GP Caterpillar parts
14H
Rating:
Alternative (cross code) number:
CA2692560
269-2560
2692560
CA2692560
269-2560
2692560
MOTOR GRADER,
Compatible equipment models: 2692560:
For full view, you need register
Information:
Cab Bulkhead Connectors
Illustration 5 g01438166
Two cab bulkhead 70 contact connectors that pass many of the Machine ECM and Implement ECM circuits through the cab wall
(1) CH-C10 Upper 70 contact connector (Implement ECM circuits)
(2) CH-C2 Lower 70 contact connector (Machine ECM circuits) Most of the Machine ECM circuits and the Implement ECM circuits that are for chassis mounted components pass through the lower right hand cab wall in two 70 contact bulkhead connectors.The lower CH-C2 bulkhead connector connects a large number of circuits from the "CH" machine wiring harness that is outside of the cab to the "C-C1" harness connector for Machine ECM circuits inside of the cab.The upper CH-C10 bulkhead connector connects a large number of circuits from the "CH" machine wiring harness that is outside of the cab to the "RH-C6" harness connector for the Implement ECM circuits inside of the cab.When troubleshooting an ECM circuit for a component that is located outside of the cab, the bulkhead connectors provide a good check point in a circuit that will help to isolate the location of the problem.Disconnect the bulkhead connector on the outside of the cab. At the disconnected bulkhead connector, check the suspect circuit for short circuits, open circuits or poor connections at the appropriate connector contacts. This will help to determine whether the problem is in the chassis section of the circuit or if the problem is in the cab section of the circuit.The lower bulkhead connector is used for Machine ECM circuits and the upper bulkhead connector is used for Implement ECM circuits.The following illustrations show the connector contacts and the circuit assignments for the upper 70 contact bulkhead connector and the lower 70 contact bulkhead connector for the chassis CH machine wiring harness.
Illustration 6 g01438886
Chassis side 70 contact bulkhead connector (same contact numbers as the ECM connectors)
Illustration 7 g01438888
Lower bulkhead harness connector CH-C2 circuit assignments
Illustration 8 g01438891
Upper bulkhead harness connector CH-C10 circuit assignments
Illustration 5 g01438166
Two cab bulkhead 70 contact connectors that pass many of the Machine ECM and Implement ECM circuits through the cab wall
(1) CH-C10 Upper 70 contact connector (Implement ECM circuits)
(2) CH-C2 Lower 70 contact connector (Machine ECM circuits) Most of the Machine ECM circuits and the Implement ECM circuits that are for chassis mounted components pass through the lower right hand cab wall in two 70 contact bulkhead connectors.The lower CH-C2 bulkhead connector connects a large number of circuits from the "CH" machine wiring harness that is outside of the cab to the "C-C1" harness connector for Machine ECM circuits inside of the cab.The upper CH-C10 bulkhead connector connects a large number of circuits from the "CH" machine wiring harness that is outside of the cab to the "RH-C6" harness connector for the Implement ECM circuits inside of the cab.When troubleshooting an ECM circuit for a component that is located outside of the cab, the bulkhead connectors provide a good check point in a circuit that will help to isolate the location of the problem.Disconnect the bulkhead connector on the outside of the cab. At the disconnected bulkhead connector, check the suspect circuit for short circuits, open circuits or poor connections at the appropriate connector contacts. This will help to determine whether the problem is in the chassis section of the circuit or if the problem is in the cab section of the circuit.The lower bulkhead connector is used for Machine ECM circuits and the upper bulkhead connector is used for Implement ECM circuits.The following illustrations show the connector contacts and the circuit assignments for the upper 70 contact bulkhead connector and the lower 70 contact bulkhead connector for the chassis CH machine wiring harness.
Illustration 6 g01438886
Chassis side 70 contact bulkhead connector (same contact numbers as the ECM connectors)
Illustration 7 g01438888
Lower bulkhead harness connector CH-C2 circuit assignments
Illustration 8 g01438891
Upper bulkhead harness connector CH-C10 circuit assignments
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts wheel Caterpillar catalog:
120H, 12H, 14H, 14H NA, 16H NA
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H, 3...
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H, 3...