WHEEL AS 3288823 - Caterpillar

3288823 WHEEL AS Caterpillar parts 272D, 272D XHP

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA3288823
328-8823
3288823

Weight: 52 pounds 23 kg.

Buy WHEEL AS 3288823 Caterpillar genuine, new aftermarket tractor parts with delivery
SKID STEER LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

V Ribbed Belt BLKPRO OEM Replacement for Cummins Engine Parts 8PK1475 3288823 3288834 3903093 3911565

$78.99

06 Jan 2025
1.0[0.45] Pounds
US: blk diesel

V Ribbed Belt BLKPRO OEM Replacement for Cummins Engine Parts 8PK1475 3288823 3288834 3903093 3911565
BLKPRO ISB QSB QSC 4B K38 B5.9 6B QSM11 ISM11 ISX15 QSX15 N855 N14 M11 B6.7 Truck Engine K19 NT855 L10 NTC NH K38 K50 Genset Industry Agriculture

$26.99

06 Jan 2025
1.0[0.45] Pounds
US: blk diesel

New Multi V Drive Belt Fan Belt for Cummins Engine Part 8PK1475 3288823 3288834 3903093 3911565 Serpentine Belt HZGladoo

$29.99

02 Aug 2024
0.5[0.23] Pounds
CN: GoodGL Parts

New Multi V Drive Belt Fan Belt for Cummins Engine Part 8PK1475 3288823 3288834 3903093 3911565 Serpentine Belt HZGladoo
HZGladoo Part number: 8PK1475 3288823 3288834 3903093 3911565 || Application : For Cummins Engine Part || Weight: 0.195 kg || Warranty: 1.5 year

For full view, you need register

Compatible equipment models: 3288823:

SKID STEER LOADER 272D 272D XHP Caterpillar

Information:

Illustration 1 g01451872
Connections of the upshift solenoid
This diagnostic code is associated with the upshift switch. The upshift switch is connected to two inputs of the ECM. One contact is open and the other contact is grounded during proper operation. This FMI 03 means that the ECM has determined that both circuits are open.Possible causes of this diagnostic code are listed:
There is a failure in the harness.
The switch has failed.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all of the connections in the circuit are clean and secure. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0622 FMI 03 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.
Table 1
Upshift Switch
Switch Position G760-WH(White) Circuit
N/O J1-41 G768-GN(Green) Circuit
N/C J1-40
Depressed Closed Open
Released Open Closed Test Step 1. CHECK THE GROUND CIRCUIT OF THE SWITCH IN THE HARNESS
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector from the switch harness assembly.
Measure the resistance between contact 2 (wire 202-BK(Black)) of the machine harness and frame ground. Expected Result:The resistance is less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. The circuit is correct. Proceed to Test Step 2.
NOT OK - The resistance is greater than 5000 ohms. The circuit is open. The machine harness has failed.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE OPERATION OF THE SWITCH IN THE RELEASED POSITION
The machine harness remains disconnected from the switch harness assembly.
Connect