AVSPARE.COM
parts catalog

WHEEL & TIRE AR 3657282 - Caterpillar



3657282 WHEEL & TIRE AR Caterpillar parts 434F, 444F WHEEL
Rating:
30
Alternative (cross code) number:
CA3657282
365-7282
3657282
Caterpillar 3657282 WHEEL & TIRE AR

Buy WHEEL & TIRE AR 3657282 Caterpillar genuine, new aftermarket tractor parts with delivery
BACKHOE LOADER,

Compatible equipment models: 3657282:

BACKHOE LOADER  434F   444F   Caterpillar
  For full view, you need register

Information:


Electrical shock hazard. The electronic unit injector system uses 90-120 volts.
Remove the valve cover and look for broken parts. Repair any broken parts or replace any broken parts that are found. Inspect all wiring for the solenoids. Look for loose connections. Also look for frayed wires or broken wires. Ensure that the connector for the unit injector solenoid is properly connected. Perform a pull test on each of the wires.
Look for signs of fuel leakage. Investigate the source of the leaking fuel. Remedy the cause of the fuel leak.
Check the valve lash setting for the cylinder of the suspect unit injector. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust".
Ensure that the bolts that hold the unit injector are tightened to the proper torque. In order to check the torque, loosen the bolts that hold the unit injector. Tighten the bolts to the proper torque. Refer to either the Disassembly and Assembly Manual , "Unit Injector - Install" or the Specifications Manual , "Unit Injector" for the proper tightening procedure.
Remove the suspect unit injector and check the unit injector for signs of exposure to coolant. Exposure to coolant will cause rust to form on the injector. If the unit injector shows signs of exposure to coolant, remove the injector sleeve and inspect the injector sleeve. Replace the injector sleeve if the injector sleeve is damaged. Check the unit injector for an excessive brown discoloration that extends beyond the injector tip. If excessive discoloration is found, check the quality of the fuel. Refer to Testing and Adjusting, "Fuel Quality - Test". Replace the seals on the injector and reinstall the injector. Refer to Disassembly and Assembly Manual, "Unit Injector - Install". Also refer to Disassembly and Assembly Manual, "Unit Injector Sleeve - Install". Inspect the injector for deposits of soot that are above the surface of the seat of the injector. Deposits of soot indicate combustion gas leakage. The source of the leak should be found, and the source of the leak should be remedied. The injector will not need to be replaced if combustion gas leakage was the problem.
If the problem is not resolved, replace the suspect injector with a new injector. In order to verify that the new injector is working properly, perform the Cylinder Cutout Test. Use the Caterpillar Electronic Technician (ET).

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts wheel Caterpillar catalog:

3728394 WHEEL AS
416E, 416F, 422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3728393 WHEEL AS
414E, 416E, 434E, 434F, 444F
2520378 WHEEL & TIRE AR
216B, 216B3, 226B, 226B3, 232B, 236D, 242B, 242B3, 242D
2384639 WHEEL AR
TH460B, TH560B, TH580B
2805030 WHEEL GP-IDLER
247, 247B, 247B3, 257B, 257B3
1426366 WHEEL & TIRE GP
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 160H, 160H NA
2548061 WHEEL & TIRE AR
120K, 120K 2, 120M, 12M
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.