AVSPARE.COM
parts catalog

WHEEL & FINAL DRIVE GP 3715138 - Caterpillar


3715138 WHEEL & FINAL DRIVE GP Caterpillar parts 980H, 980K, 980K HLG, 980M
Rating:
71
Alternative (cross code) number:
CA3715138
371-5138
3715138
Caterpillar 3715138 WHEEL & FINAL DRIVE GP
Weight: 917 pounds 415 kg.

Buy WHEEL & FINAL DRIVE GP 3715138 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Related part:
3715138  WHEEL GP-FDR&  10R7445  R

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$1,293.57
 

22 Apr 2022

US: Theodore's
Stock Bore Sprocket - 80/1 in, A Hub, 22 Teeth, 0.9375 in Stock Bore, Stainless Steel Material
Generic chain number & pitch: 80/1 in || pitch diameter: 7.0270 in || chain/sprocket type: Standard Roller Chain || maximum bore diameter: 5.9219 in || hub outside diameter: 0.0000 in
Number on catalog scheme:
  For full view, you need register

Compatible equipment models: 3715138:

WHEEL LOADER  980H   980K   980K HLG   980M   Caterpillar

Information:

Which Generate This Code:This diagnostic code is recorded when the second output driver in the MSS ECM is shorted to ground. This circuit is not used on all machines. Check for the presence of wires at contact 5 and contact 52 before you perform the procedure.The possible causes of this diagnostic code are listed below:
The wiring in the machine harness has failed.
The driven component in the circuit has failed.
The ECM has failed. This is unlikely.Test Step 1. CHECK THE WIRING HARNESS.
Disconnect the wiring harness connector from the MSS ECM.
Measure the resistance between pin 18 in the wiring harness and a ground on the machine.Expected Result:The resistance is greater than 5000 Ohms.Results:
YES - The resistance is greater than 5000 Ohms (no continuity). Harness circuit resistance is correct. Proceed to Test Step 3.
NO - Resistance is less than 5000 Ohms (continuity). The machine harness is faulty. There is a short between frame ground and the machine harness. The driven component in the circuit may also be bad. Proceed to Test Step 2.Test Step 2. CHECK THE COMPONENT.
Trace the harness to the driven component in the circuit. The component will be a relay. The component may also be a solenoid.
Measure the resistance of the component. Measure the resistance from each terminal to the case of the component.Expected Result:The resistance is greater than 5000 Ohms.Results:
YES - The resistance of the driven component is greater than 5000 Ohms (no continuity). The component is good. The machine harness has failed. There is a short between frame ground and the machine harness.Repair: Check the harness for signs of damage. Repair the machine harness or replace the machine harness. Stop.
NO - Resistance is less than 5000 Ohms (continuity). The driven component has failed. Repair: Replace the component that has failed. Stop.Test Step 3. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Remove the connector from the ECM. Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the key start switch to the ON position.
Clear all inactive diagnostic codes.
Operate the machine.
Determine if CID 1392 FMI 04 is present.Expected Result:CID 1392 FMI 04 is present.Results:
YES - CID 1392 FMI 04 is present.Repair: The problem has not been corrected. It is unlikely that the ECM has failed. Perform the previous Steps again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". Stop.
NO - CID 1392 FMI 04 is not present.Repair: The diagnostic code is NOT present. The problem does not exist at this time. The initial problem was probably caused by an intermittent short in the wiring harness. Inspect the harness for any signs of damage. If the harness passes through a hole with a grommet, that area of the harness can become chafed. This may cause an intermittent short. The harness may also be damaged in locations that could pinch the harness. Repair any wiring that could have caused the problem. Resume normal machine operation. Stop.

Cat SIS web machinery list:

Caterpillar parts catalog
980M Wheel Loader WW300001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader MK200001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader MGD00001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader XDJ00001-UP (MACHINE) POWERED BY C13 Engine
980H Wheel Loader JMS00001-UP (MACHINE) POWERED BY C15 Engine
980K Wheel Loader W7K00001-UP (MACHINE) POWERED BY C13 Engine
980K Wheel Loader GTZ00001-UP (MACHINE) POWERED BY C13 Engine
980H Wheel Loader KZL00001-UP (MACHINE) POWERED BY C15 Engine
980M Wheel Loader KRS00001-UP (MACHINE) POWERED BY C13 Engine
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine
980K Wheel Loader High Lift Grapple NEP00001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader N8T00001-UP (MACHINE) POWERED BY C13 Engine
980L Wheel Loader D8Z00001-UP (MACHINE) POWERED BY C13 Engine


Parts wheel Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.