AVSPARE.COM
parts catalog

WHEEL & TIRE GP 3728392 - Caterpillar



3728392 WHEEL & TIRE GP Caterpillar parts 434F, 444F WHEEL
Rating:
13
Alternative (cross code) number:
CA3728392
372-8392
3728392
Caterpillar 3728392 WHEEL & TIRE GP

Buy WHEEL & TIRE GP 3728392 Caterpillar genuine, new aftermarket tractor parts with delivery
BACKHOE LOADER,

Compatible equipment models: 3728392:

BACKHOE LOADER  434F   444F   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

full charging current of the alternator.
When jump starting an engine, the instructions in the Operation and Maintenance Manual, "Starting with Jump Start Cables" should be followed in order to properly start the engine.This engine may be equipped with a 12 volt starting system or with a 24 volt starting system. Only equal voltage for boost starting should be used. The use of a welder or of a higher voltage will damage the electrical system.
The engine has several input components which are electronic. These components require an operating voltage.This engine is tolerant to common external sources of electrical noise. Electromechanical buzzers can cause disruptions in the power supply. If electromechanical buzzers are used near the system, the engine electronics should be powered directly from the battery system through a dedicated relay. The engine electronics should not be powered through a common power bus with other devices that are activated by the engine control switch (ECS).Engine Electrical System
The electrical system can have three separate circuits. The three circuits are the charging circuit, the starting circuit, and the low amperage circuit. Some of the electrical system components are used in more than one circuit.The charging circuit is in operation when the engine is running. An alternator creates electricity for the charging circuit. A voltage regulator in the circuit controls the electrical output in order to maintain the battery at full charge.The starting circuit is in operation when the start switch is activated.The low amperage circuit and the charging circuit are connected through the ammeter. The starting circuit is not connected through the ammeter.Charging System Components
Alternator
The alternator is driven by the crankshaft pulley through a belt that is a Poly-vee type. This alternator is a three-phase self-rectifying charging unit. The regulator is part of the alternator.The alternator design has no need for slip rings or for brushes. The only part of this alternator that moves is the rotor assembly. All of the conductors that carry current are stationary. The following components are the conductors: the field winding, the stator windings, six rectifying diodes and the regulator circuit.The rotor assembly has many magnetic poles with air space between each of the opposite poles. The poles have residual magnetism that produces a small amount of magnet-like lines of force (magnetic field). This magnetic field is produced between the poles. As the rotor assembly begins to turn between the field winding and the stator windings, a small amount of alternating current (AC) is produced in the stator windings. The alternating current is produced from the small magnetic lines of force that are created by the residual magnetism of the poles. The AC is changed into direct current (DC) when the current passes through the diodes of the rectifier bridge. Most of this current provides the battery charge and the supply for the low amperage circuit. The remainder of current is sent to the field windings. The DC current flow through the field windings (wires around an iron core) increases the strength of the magnetic lines

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
434F Backhoe Loader LDH00001-UP (MACHINE) POWERED BY C4.4 Engine
444F Backhoe Loader LJJ00001-UP (MACHINE) POWERED BY C4.4 Engine
444F Backhoe Loader Side Shift JXR00001-UP (MACHINE) POWERED BY C4.4 Engine
434F Backhoe Loader MTR00001-UP (MACHINE) POWERED BY C4.4 Engine
444F2 Side Shift Backhoe Loader HWS00001-UP (MACHINE) POWERED BY C4.4 Engine
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
444F Backhoe Loader FBN00001-UP (MACHINE) POWERED BY C4.4 Engine
434F2 Side Shift Backhoe Loader LYK00001-UP (MACHINE) POWERED BY C4.4 Engine
444F2 Side Shift Backhoe Loader LYL00001-UP (MACHINE) POWERED BY C4.4 Engine
434F2 Side Shift Backhoe Loader HWR00001-UP (MACHINE) POWERED BY C4.4 Engine


Parts wheel Caterpillar catalog:

3728394 WHEEL AS
416E, 416F, 422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3728393 WHEEL AS
414E, 416E, 434E, 434F, 444F
9R5498 WHEEL & TIRE GP-REAR
416, 416B, 426, 426B, 428, 428B
1426353 WHEEL & TIRE GP
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 160H, 160H NA, 160K
2011877 WHEEL & TIRE GP
416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 430D, 430E
2520762 WHEEL & TIRE GP
120M, 12M, 140M, 160M
2547890 WHEEL & TIRE GP
120M, 120M 2, 12M, 12M 2, 12M 3, 140M, 140M 2, 140M 3, 160M 2, 160M 3
9R6191 WHEEL & TIRE GP-FRONT
416, 416B, 426, 426B, 428, 428B, 428C, 436, 436B, 438B
2520719 WHEEL & TIRE GP
120K, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD
3291355 WHEEL & TIRE GP
416F, 422E, 422F, 428E, 428F, 432E, 432F, 442E
1G3605 WHEEL & TIRE GP
CP-563, CS-531, CS-531C, CS-531D, CS-533C, CS-533D, CS-563C, CS-563D, CS-573C, CS-573D, CS-583C, CS-583D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.