AVSPARE.COM
parts catalog

WHEEL 4415978 - Caterpillar



4415978 WHEEL Caterpillar parts SAT318 WHEEL
Rating:
80
Alternative (cross code) number:
CA4415978
441-5978
4415978
Caterpillar 4415978 WHEEL
Weight: 28 pounds 13 kg.

Buy WHEEL 4415978 Caterpillar genuine, new aftermarket tractor parts with delivery
HARVESTER HEAD,

Compatible equipment models: 4415978:

HARVESTER HEAD  SAT318   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:

5 Put the 5P5212 Plate (7) on stud (3) so the plate is against head (6).6 Put 5P5201 Cylinder (8) on stud (3) until the cylinder makes contact with plate (7).7 Put 5P5208 Nut (9) on stud (3) and turn the nut until it is 6.4 (0.25") from cylinder (8). Connect a hydraulic pump to cylinder (8). Hold sleeve (5) and head (6) in alignment and put enough force on the cylinder to push the bearing cone on the hub until it is against spacer (1).
Do not use more than 180 kN (20) of force. BE SURE THE PISTON OF CYLINDER (8) IS RETRACTED BEFORE THE CYLINDER IS REMOVED.
8 Install the remainder of the parts as given in the Service Manual.Sprocket Removal - D9, DD9, SxSD9, 594
1 Remove the nut and lock ring that fasten the sprocket to the hub assembly. See the Service Manual for procedure.2 Put 6V3123 Adapters (1) in the puller holes in the sprocket. Use 6V3124 Nuts (2) to fasten adapters (1) in position. Install each nut so the flat end of the nut is even with the end of the threads on the adapter and drill point (3) is toward the O.D. of the sprocket. The angle face of the nut must be toward the sprocket. On the 594 (62H1-62H319), make sure the nuts fit flat against the milled pad on the back of the sprocket. If necessary, machine the pad for correct fit.3 Put 5P5209 Adapter (4) on the hub assembly. Turn the adapter until it is against the hub assembly. Install 5P5207 (5) in adapter (4).4 Put 6V3128 Spreader (6) in position on adapter (4) as shown. Slide 5P5201 Cylinder (7), with the piston end away from the sprocket, over stud (5) until it comes in contact with adapter (4). Spreader (6) is not used on the 594, and on D9 sprockets where the slope of the disc is inward from the segments toward the machine.5 Put 6V4000 Head (8) on stud (5) and slide the head, with the flat side toward the sprocket, against the cylinder. Use 6V3126 Pins (9) and the 5P8837 Locks to fasten 6V3125 Arms (10) to adapters (1), spreader (6) and head (8). Spreader (6) has two sets of alignment holes; use the inner holes for sprockets with puller holes on a 635Ø (25.0"Ø) or the outer holes for sprockets with puller holes on a 686Ø (27.0"Ø) circle.6 Connect a hydraulic pump to cylinder (7) and tighten arms (10). Put 5P5208 Nut (11) on stud (5) until it is 25.4 (1.00") from head (8). Remove the sprocket. BE SURE THE PISTON OF CYLINDER (7) IS RETRACTED BEFORE THE CYLINDER IS REMOVED.
Do not put a load of more than 1335 kN (150) on the tools.
Sprocket Installation - D9, DD9, SxSD9, 594
1 Put sprocket (1) on the final drive hub. Make sure the Duo-Cone Seals are clean and dry. Put a small amount of clean oil on the metal surfaces in contact with each other. Install

Caterpillar parts catalog:

Caterpillar parts catalog
SAT322 HARVESTER HEAD SH800001-UP (MACHINE)


Parts wheel Caterpillar catalog:

4398748 WHEEL-DRIVE
SAT318, SAT318T, SAT322
4398703 WHEEL AS
SAT318, SAT318T, SAT322
4398702 WHEEL AS
SAT318, SAT318T, SAT322
4377291 WHEEL AS-MEASURING
SAT223, SAT318, SAT318T, SAT322
4501196 WHEEL
SAT22DB, SAT322
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.