AVSPARE.COM
parts catalog

WHEEL & TIRE AR 5088641 - Caterpillar



5088641 WHEEL & TIRE AR Caterpillar parts WHEEL
Rating:
26
Alternative (cross code) number:
CA5088641
508-8641
5088641
Caterpillar 5088641 WHEEL & TIRE AR

Buy WHEEL & TIRE AR 5088641 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:

Troubleshooting Overview
Flash programming is a method of programming or updating the flash file in the Electronic Control Module (ECM). Cat® Electronic Technician (ET) is used to flash program a file into the memory of the ECM.Note: Customer versions of Cat ET do not have the capability for flash programming. Consult your local Cat Dealer for assistance.If you do not have the flash file, use the "Flash File Search" tool on the Service Technician Workbench (STW) to obtain the flash file for your machine. Alternatively, use the "Service Software Files" feature on SIS Web to obtain the flash file for your machine. You must have the machine serial number to search for the flash file. After locating the correct flash file, download the flash file to your PC. Write down the name of the flash file for future reference.Troubleshooting Procedure
Table 1
Troubleshooting Test Steps Values Results
1. Programming a Flash File
A. Establish communication between Cat ET and the ECM.
B. Download an ECM replacement file. This file will help in the transfer of saved configurations for the Implement ECM and calibration values for solenoids and linkage sensors.
C. Select "WinFlash" from the "Utilities" menu on Cat ET.
If "WinFlash" will not communicate with the ECM, refer to Troubleshooting, "Electronic Service Tool Does Not Communicate".
D. Program the flash file into the ECM.
E. Select the appropriate ECM under the "Detected ECM modules".
F. Press the "Browse" button to select the name of the flash file that will be programmed into the ECM.
G. When the correct flash file is selected, press the "Open" button.
H. Verify that the "File Values" match the application. If the "File Values" do not match the application, obtain the correct flash file.
J. When the correct flash file is selected, press the "Begin Flash" button.
K. Cat ET will indicate when flash programming has been successfully completed.
L. Start the machine and check for proper operation. Repair any active diagnostic or event codes.
Programmed successfully. Result: The flash programming was successful.
Return the unit to service.
Result: The flash programming was not successful.
Repair any active diagnostic or event codes. Proceed to Test Step 2.
2. "WinFlash" Error Messages
A. If you receive any error messages during flash programming, click on the "Cancel" button to stop the process. Access the information about the "ECM Summary" under the "Information" menu. Make sure that you are flashing the correct file for your machine.
B. Record all error messages. The recorded error messages will be necessary if further assistance is needed.
Error messages. Result: There are no error messages.
Return the unit to service.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
426F2 Backhoe Loader Side Shift DJ400001-UP (MACHINE) POWERED BY C4.4 Engine
424B2 Backhoe Loader Side Shift JTH00001-UP (MACHINE)
424B Backhoe Loader Side Shift JRN00001-UP (MACHINE)
424B HD Backhoe Loader JRY00001-UP (MACHINE)


Parts wheel Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.