WINDOW GP 1145341 - Caterpillar

1145341 WINDOW GP Caterpillar parts 312, 315, 317

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1145341
114-5341
1145341

Weight: 17 pounds 8 kg.

Buy WINDOW GP 1145341 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

$576.24

10 Nov 2020

-: -

Maine 1145341 Silver Membrane Filter, 0.45µm Pore Size, 37 mm Size (Pack of 25)
0.45µm pore size || 37mm size || Pack of 25 || 0 || 0

This part in 1 request: Show. This information for suppliers only!

#62582 1145341

2017-05-17

Number on catalog scheme: 26

Caterpillar 1145341 Parts scheme WINDOW GP

For full view, you need register

Compatible equipment models: 1145341:

EXCAVATOR 312 315 317 Caterpillar

Information:

Illustration 1 g01302386
Schematic of the Clutch Solenoid "1 - Reverse"This diagnostic code is associated with the Clutch Solenoid "1 - Reverse". The FMI 06 means that the ECM has determined that the current of the solenoid is above normal.The possible causes of this diagnostic code are listed:
The solenoid energizer circuit of the modulating valve is shorted to ground.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1401 FMI 06 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code is active, the ECM will turn off the current to the failed solenoid.Test Step 1. CHECK THE SOLENOID
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness.Expected Result:CID 1401 FMI 06 changes to CID 1401 FMI 05 when the solenoid is disconnected.Results:
YES - CID 1401 FMI 06 changes to CID 1401 FMI 05 when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid.STOP
NO - CID 1401 FMI 06 remains active. Proceed to Test Step 2.Test Step 2. CHECK THE SOLENOID ENERGIZER CIRCUIT FOR A SHORT TO GROUND
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector, measure the resistance from the signal contact J1-17 (wire 751-GN) to all contacts that are used in the machine harness connectors for the ECM.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-17 (wire 751-GN) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS
Inspect the harness connectors and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 1401 FMI 06.Expected Result:The CID 1401 FMI 06 is active.Results:
YES - The CID 1401 FMI 06 is active.