1G5948 WIRE AS Caterpillar parts
AP-1050
Rating:
Alternative (cross code) number:
CA1G5948
1G-5948
1G5948
CA1G5948
1G-5948
1G5948
Weight: 0.21 pounds 0 kg.
ASPHALT PAVER,
Compatible equipment models: 1G5948:
Information:
Illustration 1 g02327815
Schematic for the Stick In Limit solenoid This diagnostic code is associated with the Stick In Limit solenoid. An FMI 06 diagnostic code Indicates the Machine ECM has determined the solenoid circuit current is above normal. For machines equipped with the E-Fence feature, reference Troubleshooting, " E-Ceiling and Cab Avoidance - Troubleshoot"Possible causes for this diagnostic code are listed below:
The Back Up Crane switch has failed.
The energize circuit of the solenoid is shorted to ground.
The ECM may have failed (unlikely).Note: When this diagnostic code is activated, verify that there are no other active diagnostic codes for the Stick Out Limit solenoid. Those other active diagnostic codes for the solenoid must be cleared before starting this procedure.Note: Poor connections are often the cause of a problem in electrical circuits. Before performing this procedure, inspect all the machine harnesses and connectors involved in the circuit. Make sure to verify that all of the connections in the circuit are clean, secure, and in good condition. Correct any problems found with any of the connections. Verify the diagnostic code CID 2422 FMI 06 is still active, before continuing with this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes now, but clear those diagnostic codes when the original diagnostic code has been corrected. Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Disconnect the harness connector from the Stick In Limit solenoid.
Observe the status of the CID 2422 FMI 06 diagnostic code. Expected Result:The CID 2422 FMI 06 diagnostic code stays active. Results:
YES - The CID 2422 FMI 06 diagnostic code stays active. The solenoid is not the cause of the problem Go to Test Step 2.
NO - The CID 2422 FMI 06 diagnostic code is not active. The solenoid has failed.Repair: Replace the solenoid. Go to Test Step 3.Test Step 2. CHECK THE SOLENOID ENERGIZE CIRCUIT FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect both the J1 and J2 harness connector from the ECM.
At the ECM harness connectors, measure the resistance from contact J2-13 (wire K928-GN) to all of the other contacts that are used in both the J1 and J2 ECM harness connectors. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
YES - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Go to Test Step 3.
NO - A resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-13 wire (K928-GN) and the wire with the low resistance measurement.Repair: Repair or replace the machine harness. Go to Test Step 3.Test Step 3. CHECK THE DIAGNOSTIC CODE STATUS.
Reconnect all harness connectors. Make sure that the connectors are fully seated. Observe that the clips on each connector are fastened securely.
Turn the disconnect switch and the key start switch to the
Caterpillar parts catalog:
Parts wire Caterpillar catalog:
9Y8241
WIRE AS
205B, 214B, 224B, 3114, 3116, 3126, 3126B, 320 L, 322, 325, 325 LN, 35, 45, 55, AP-1000, AP-1050, C7, CB-434, CP-563, E110B, E120B, E240C, RT100
205B, 214B, 224B, 3114, 3116, 3126, 3126B, 320 L, 322, 325, 325 LN, 35, 45, 55, AP-1000, AP-1050, C7, CB-434, CP-563, E110B, E120B, E240C, RT100
7R6226
WIRE AS
AP-1000, AP-1050, AP-800
AP-1000, AP-1050, AP-800
6R0490
WIRE AS
AP-1000, AP-1050, AP-800
AP-1000, AP-1050, AP-800
7R5005
WIRE AS
AP-1050
AP-1050
7R3038
WIRE AS
AP-1000, AP-1050, AP-800
AP-1000, AP-1050, AP-800
7R3046
WIRE AS
AP-1000, AP-1050, AP-800
AP-1000, AP-1050, AP-800
7R3136
WIRE AS
AP-1050, AP-800
AP-1050, AP-800
6R0777
WIRE AS
AP-1050, AP-800
AP-1050, AP-800
1G7096
WIRE AS
AP-1000, AP-1050, AP-800
AP-1000, AP-1050, AP-800
6R1471
WIRE AS
AP-1050
AP-1050
7R3137
WIRE AS
AP-1050, AP-800
AP-1050, AP-800
7R3139
WIRE AS
AP-1050, AP-800
AP-1050, AP-800
7R3138
WIRE AS
AP-1050, AP-800
AP-1050, AP-800
7R3345
WIRE AS
AP-1050, AP-800
AP-1050, AP-800
6R0491
WIRE AS
AP-1000, AP-1050, AP-800
AP-1000, AP-1050, AP-800
7R3136
WIRE AS
AP-1050, AP-800
AP-1050, AP-800
1210143
WIRE AS
AP-1000, AP-1050
AP-1000, AP-1050
1438929
WIRE-LOCK
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-800C, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C, CB-534C, CS-531C, CS-531D, CS-533C, CS-563C, CS-563D, CS-573D, CS-583C, CS-583D, CW-14, PF-290B, PS-150B, P...
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-800C, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C, CB-534C, CS-531C, CS-531D, CS-533C, CS-563C, CS-563D, CS-573D, CS-583C, CS-583D, CW-14, PF-290B, PS-150B, P...
7R0353
WIRE AS
AP-1000, AP-1050, AP-800
AP-1000, AP-1050, AP-800
7R0354
WIRE AS
AP-1000, AP-1050, AP-800
AP-1000, AP-1050, AP-800
7R0355
WIRE AS
AP-1000, AP-1050, AP-800
AP-1000, AP-1050, AP-800