3C8052 WIRE A Caterpillar parts
Rating:
Alternative (cross code) number:
CA3C8052
3C-8052
3C8052
CA3C8052
3C-8052
3C8052
Weight: 17 pounds 8 kg.
For full view, you need register
Information:
Removal Procedure
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Engine Oil - Change".
Illustration 1 g01174241
Remove bolts (2) . Remove engine oil pan (1) and the gasket.Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 598 Black High Performance RTV Silicone Gasket Maker -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01174241
Illustration 3 g00612810
Clean the mating surface of engine oil pan (1) and the cylinder block. Apply Tooling (A) to four areas on the sealing surface of the oil pan. The areas are Marked Location (Y) .
Place a new gasket and engine oil pan (1) on the cylinder block.
Tighten four Oil Pan Bolts (X) .
Start with Bolt (Z) and tighten all remaining bolts (2) in a counterclockwise sequence.
Tighten bolts (2) to a torque of 31 1 N m (23 1 lb ft).
Start again with Bolt (Z) and tighten all remaining bolts in a counterclockwise sequence.
Tighten bolts (2) again to a torque of 31 1 N m (23 1 lb ft).
Fill the engine with oil to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil - Change" and Operation and Maintenance Manual, "Capacities (Refill)".
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Drain the engine oil into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Engine Oil - Change".
Illustration 1 g01174241
Remove bolts (2) . Remove engine oil pan (1) and the gasket.Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 598 Black High Performance RTV Silicone Gasket Maker -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01174241
Illustration 3 g00612810
Clean the mating surface of engine oil pan (1) and the cylinder block. Apply Tooling (A) to four areas on the sealing surface of the oil pan. The areas are Marked Location (Y) .
Place a new gasket and engine oil pan (1) on the cylinder block.
Tighten four Oil Pan Bolts (X) .
Start with Bolt (Z) and tighten all remaining bolts (2) in a counterclockwise sequence.
Tighten bolts (2) to a torque of 31 1 N m (23 1 lb ft).
Start again with Bolt (Z) and tighten all remaining bolts in a counterclockwise sequence.
Tighten bolts (2) again to a torque of 31 1 N m (23 1 lb ft).
Fill the engine with oil to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil - Change" and Operation and Maintenance Manual, "Capacities (Refill)".