3C8380 WIRE ASSEMBLY Caterpillar parts
Rating:
Alternative (cross code) number:
CA3C8380
3C-8380
3C8380
CA3C8380
3C-8380
3C8380
Weight: 1 pounds 0 kg.
For full view, you need register
Information:
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1 Start By:
Remove the lockup clutch and solenoid valve. Refer to Disassembly and Assembly, "Lockup Clutch and Solenoid Valve - Remove". Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
Illustration 1 g01186262
Illustration 2 g01186279
Remove screws (5), manifold assembly (4), and the O-ring seals.
Remove nut (1) and coil assembly (2).
Remove cartridge assembly (7) from the manifold (8).
Remove bolts (3) and cover assembly (6).
Illustration 3 g01186311
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Remove plug (9), slug (10), spring (11), spool assembly (12), and springs (13).
Illustration 4 g01186322
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Use Tooling (A) in order to remove retaining ring (14), retainer (15), spring (16), and ball (17) from spool (18).
Illustration 5 g01186326
Illustration 6 g01186356
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Remove bolts (19) and cover (20).
Remove screws (21) and body (22).
Remove O-ring seal (24), orifice (25), and spring (26).
Remove pistons (23) and (27). Remove shims (28) and stop (29).
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1 Start By:
Remove the lockup clutch and solenoid valve. Refer to Disassembly and Assembly, "Lockup Clutch and Solenoid Valve - Remove". Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
Illustration 1 g01186262
Illustration 2 g01186279
Remove screws (5), manifold assembly (4), and the O-ring seals.
Remove nut (1) and coil assembly (2).
Remove cartridge assembly (7) from the manifold (8).
Remove bolts (3) and cover assembly (6).
Illustration 3 g01186311
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Remove plug (9), slug (10), spring (11), spool assembly (12), and springs (13).
Illustration 4 g01186322
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Use Tooling (A) in order to remove retaining ring (14), retainer (15), spring (16), and ball (17) from spool (18).
Illustration 5 g01186326
Illustration 6 g01186356
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Remove bolts (19) and cover (20).
Remove screws (21) and body (22).
Remove O-ring seal (24), orifice (25), and spring (26).
Remove pistons (23) and (27). Remove shims (28) and stop (29).