AVSPARE.COM
parts catalog

WIRING KIT 0878398 - Caterpillar



0878398 WIRING KIT Caterpillar parts WIRING
Rating:
11
Alternative (cross code) number:
CA0878398
087-8398
0878398
Caterpillar 0878398 WIRING KIT

Buy WIRING KIT 0878398 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 2 g03713908
Right Operator Display
(12) Operator display
(13) Machine direction icon
(14) Actual machine speed
(15) Target machine speed
(16) Steering percentage icon
(17) Steering value
(18) Steering direction Each instrument panel is equipped with operator display (12). The display communicates with the ECMs on the machine through CAN "A". When the display is on the operator screen, the upper information banner shows propel and steering data.Machine direction icon (13) indicates the target machine direction. Actual machine speed (14) is shown to the right of the machine direction icon. Target machine speed (15) is shown to the right of the target icon. In the maneuver and pave modes, speed is displayed in meters per minute or feet per minute. In travel mode, speed is displayed in kilometers per hour or miles per hour. Machine speed units depend on the display units chosen.Steering percentage icon (16) indicates steering direction (18) and steering value (17). The arrows of the steering direction indicate actual steering direction. The steering value is displayed as a percentage value. When the steering wheel is in the straight travel position, the steering value is zero. When the steering wheel is turned, the steering value increases. When the steering wheel reaches either stop, the steering value will be 100.
Illustration 3 g03713910
Set Hill Mode
(19) Machine icon
(20) Operator screen
(21) Machine screen
(22) Settings screen
(23) Propel screen
(24) Hill Hold screen The machine control system is programmed with hill-mode logic. This logic prevents the machine from rolling backwards on steep inclines during the transition between neutral and forward while in pave mode. The operator can use the display to enable or disable the hill-mode logic. When this logic is enabled, the transmission ECM does not release the parking brake until one of the following conditions are met:
The propel calibration offset current is achieved.
The duration of the rollback brake timer has elapsed.Hill-mode logic allows the pressure in the propel circuit to increase before the parking brake is released. Since this action increases wear on the parking brake, the feature should only be enabled while the machine is paving on steep slopes.The operator can change the status of the hill-mode logic with the following steps:
Select machine icon (19) from operator screen (20).
Select "Settings" from the "Machine" screen (21).
Select "Propel" from the "Settings" screen (22).
Select "Hill Hold" from the "Propel" screen (23).
Select "Enable" or "Disable" from the "Hill Hold" screen (24), and then, select "OK". Note: The up and down arrows on the right side of the screen allow the operator to highlight the available options. The "OK" key confirms the selected option.
Illustration 4 g03713912
Set Friction Steer
(19) Machine icon
(20) Operator screen
(21) Machine screen
(22) Settings screen
(23) Propel screen
(25) Friction steer screen The operator can use the display to change the friction steering level. The level can be changed between 80 percent and 120 percent in 10-percent increments. The operator can set the friction steering level with the following steps:
Select machine icon (19) from operator screen (20).
Select "Settings" from the "Machine" screen (21).
Select "Propel" from the "Settings" screen (22).
Select "Friction Steer" from the "Propel" screen (23).
On


Parts wiring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.