2356196 WIRING GP-LIGHTING Caterpillar parts
14M
Rating:
Alternative (cross code) number:
CA2356196
235-6196
2356196
CA2356196
235-6196
2356196
MOTOR GRADER,
Compatible equipment models: 2356196:
Number on catalog scheme:
For full view, you need register
Information:
Specification
Table 1
"Travel on Level Ground - Test"
Travel Time (time in seconds)
Travel Speed New Service Limit Actual
HIGH Forward 13.7 1.0 17.8 or less
Reverse
LOW Forward 22.6 1.5 29.4 or less
Reverse
Travel Deviation(1) mm (inch)
Travel Speed New Service Limit Actual
HIGH Forward 650 mm (25.6 inch) or less 1500 mm (59.1 inch) or less
Reverse
LOW Forward 650 mm (25.6 inch) or less 1500 mm (59.1 inch) or less
Reverse
(1) Travel deviation (distance) from the reference lineIntroduction
The performance level of the travel motors can be determined with the following procedure.Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".Required Tools
Table 2
Description Qty
Measuring Tape 1
Stopwatch 1 Machine Preparation
Illustration 1 g00296317
(A) Preliminary run 5 m (16.4 ft)
(B) Travel distance 20 m (65.6 ft)
(C) Bucket height 0.5 to 1 m (1.6 to 3.3 ft)
Travel distance must be at least 25 m (82 ft) long. Travel test ground must be hard and as level as possible.
Draw a 25 m (82 ft) straight line on travel test ground as a reference line. Test Procedure
Start the engine.
Place the machine controls at the following settings: Engine speed dial "10" and AEC switch OFF.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
The bucket should be empty.
Position the machine so that one track is parallel with the reference line. Position the machine for the travel test. Refer to Illustration 1.
Place the travel speed control switch in HIGH position.
Move the machine by operating both travel levers at the same time.
The first 5 m (16.4 ft) are for a preliminary run. Measure the travel time that is required to travel the remaining 20 m (65.6 ft). Measure the time that is required in each direction.
Measure the travel deviation from the reference line.
Place the travel speed control switch on the LOW position and repeat Steps 7 through 9.
Table 1
"Travel on Level Ground - Test"
Travel Time (time in seconds)
Travel Speed New Service Limit Actual
HIGH Forward 13.7 1.0 17.8 or less
Reverse
LOW Forward 22.6 1.5 29.4 or less
Reverse
Travel Deviation(1) mm (inch)
Travel Speed New Service Limit Actual
HIGH Forward 650 mm (25.6 inch) or less 1500 mm (59.1 inch) or less
Reverse
LOW Forward 650 mm (25.6 inch) or less 1500 mm (59.1 inch) or less
Reverse
(1) Travel deviation (distance) from the reference lineIntroduction
The performance level of the travel motors can be determined with the following procedure.Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".Required Tools
Table 2
Description Qty
Measuring Tape 1
Stopwatch 1 Machine Preparation
Illustration 1 g00296317
(A) Preliminary run 5 m (16.4 ft)
(B) Travel distance 20 m (65.6 ft)
(C) Bucket height 0.5 to 1 m (1.6 to 3.3 ft)
Travel distance must be at least 25 m (82 ft) long. Travel test ground must be hard and as level as possible.
Draw a 25 m (82 ft) straight line on travel test ground as a reference line. Test Procedure
Start the engine.
Place the machine controls at the following settings: Engine speed dial "10" and AEC switch OFF.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
The bucket should be empty.
Position the machine so that one track is parallel with the reference line. Position the machine for the travel test. Refer to Illustration 1.
Place the travel speed control switch in HIGH position.
Move the machine by operating both travel levers at the same time.
The first 5 m (16.4 ft) are for a preliminary run. Measure the travel time that is required to travel the remaining 20 m (65.6 ft). Measure the time that is required in each direction.
Measure the travel deviation from the reference line.
Place the travel speed control switch on the LOW position and repeat Steps 7 through 9.
Caterpillar SIS machinery equipment:
Parts wiring Caterpillar catalog:
3605872
WIRING GP-MONITOR
120M, 120M 2, 12M, 12M 2, 12M 3, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD
120M, 120M 2, 12M, 12M 2, 12M 3, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD
2912910
WIRING GP-CAB
120M, 12M, 140M, 14M, 160M, 16M
120M, 12M, 140M, 14M, 160M, 16M
2528000
WIRING GP-CAMERA
120M, 12M, 140M, 14M, 160M
120M, 12M, 140M, 14M, 160M
120M, 12M, 140M, 14M, 160M, 16M, 24M
2476430
WIRING GP-REAR LIGHTING
120M, 12M, 140M, 14M, 160M
120M, 12M, 140M, 14M, 160M
2333125
WIRING GP-LIGHTING
14M, 160M
14M, 160M
2474886
WIRING GP-ENGINE
C15, C18
C15, C18
4236543
WIRING GP-ELECTRONIC CONTROL
C15, C18
C15, C18
2476430
WIRING GP-REAR LIGHTING
120M, 12M, 140M, 14M, 160M
120M, 12M, 140M, 14M, 160M