AVSPARE.COM
parts catalog

WIRING GP-ENGINE ELECTRONIC 3904592 - Caterpillar



3904592 WIRING GP-ENGINE ELECTRONIC Caterpillar parts 814F II, 815F II, 816F II WIRING
Rating:
17
Alternative (cross code) number:
CA3904592
390-4592
3904592
Caterpillar 3904592 WIRING GP-ENGINE ELECTRONIC

Buy WIRING GP-ENGINE ELECTRONIC 3904592 Caterpillar genuine, new aftermarket tractor parts with delivery
LANDFILL COMPACTOR, WHEEL DOZER,

Compatible equipment models: 3904592:

LANDFILL COMPACTOR  816F II  
SOIL COMPACTOR  815F II  
WHEEL DOZER  814F II   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Thoroughly inspect ECM connectors (1). Inspect all of the connectors that are associated with the CAN data link. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 3 g01209797
Terminal locations at the P1 ECM connector that are associated with the CAN data link (P1-34) CAN data link − (P1-42) CAN shield (P1-50) CAN data link +
Illustration 4 g01209794
Terminal locations at the service tool connector that are associated with the CAN data link (Terminal C) CAN shield (Terminal F) CAN data link + (Terminal G) CAN data link −
Illustration 5 g01355248
Terminal locations at the connector for the termination resistor that are associated with the CAN data link (Terminal A) CAN data link + (Terminal B) CAN data link − (Terminal C) CAN shield
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the CAN data link.
Check the allen head screw on each ECM connector and on the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the wiring harnesses for abrasion, for corrosion and for pinch points.Expected Result:All connectors, pins and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the wiring harness.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the problem is resolved.STOPTest Step 2. Verify the Proper Installation of the Termination Resistors
Remove the electrical power from the ECM.
Disconnect any display panel from the data link.
Disconnect the Caterpillar Electronic Technician (ET) from the service tool connector.
Disconnect the P1 ECM connector.Note: Wiggle the harness during the following measurements in order to reveal an intermittent condition.
Measure the resistance between terminals P1-50 (CAN data link +) and P1-34 (CAN data link -).Expected Result:The resistance is between 57 and 63 Ohms.Results:
OK - The resistance is between 57 and 63 Ohms. Proceed to Test Step 3.
Not OK - The resistance is between 114 Ohms and 126 Ohms. A termination resistor is missing.Repair: Verify that two termination resistors are connected to the data link. One resistor must be located on each end of the data link. The engine is shipped with one termination resistor that is installed between the ECM and the customer connector.Refer to the appropriate electrical schematic in order to determine the missing resistor. Replace the missing resistor. Verify that the problem is resolved.STOP
Not OK - The resistance is less than 57 Ohms. There may be a short circuit in the harness. Proceed to Test Step 3.
Not OK - The resistance is greater than 126 Ohms. There may be an open circuit in the harness. Proceed to Test Step 4.Test Step 3. Check the Harness for a Short Circuit
Remove both termination resistors from the CAN data link.
Disconnect the display panel.
Measure the resistance between the

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
815F Series 2 Soil Compactor BYN00001-UP (MACHINE) POWERED BY C9 Engine
816F Series 2 Landfill Compactor BZR00001-UP (MACHINE) POWERED BY C9 Engine
814F Series 2 Wheel Dozer BXG00001-UP (MACHINE) POWERED BY C9 Engine


Parts wiring Caterpillar catalog:

2311935 WIRING GP-ENGINE ELECTRONIC
160M, 627G, 637D, 637E, 637G, 814F II, 815F II, 816F II, C9, CX31-C9I, TH31-E61
2688820 WIRING GP-MACHINE
814F II, 815F II, 816F II
2693410 WIRING GP-HEATER
140M, 140M 2, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 5...
3306017 WIRING GP-ENGINE ELECTRONIC
140M, 160M, 586C, 627G, 637D, 637E, 637G, 814F II, 815F II, 816F II, 973D, C9, TH31-E61
2688834 WIRING GP-ENGINE
814F II, 815F II, 816F II
2688839 WIRING GP-COMMUNICATION
814F II, 815F II, 816F II
2649601 WIRING GP-HEATER
814F II, 815F II, 816F II, C9
3358790 WIRING GP-CAB
814F II, 815F II, 816F II
2041764 WIRING GP-CONSOLE
308C, 314C, 321C, 325C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.