AVSPARE.COM
parts catalog

WIRING GP- 5088919 - Caterpillar



5088919 WIRING GP- Caterpillar parts WIRING
Rating:
11
Alternative (cross code) number:
CA5088919
508-8919
5088919
Caterpillar 5088919 WIRING GP-

Buy WIRING GP- 5088919 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:


Table 2
Required Parts    
Quantity     Part Number     Description    
2     136-7440     Shim    
2     176-0626     Washer    
2     9R-8291     Spacer    
Remove the 290-8156 Pin As from the swing frame. Refer to Disassembly and Assembly, RENR6485, "Swing Frame - Remove".
Remove the 9F-2049 Dowel from the top of the 290-8156 Pin As . Remove the 3B-8486 Grease Fitting from the bottom of the pin assembly.
Illustration 1 g01518697
Enlarge the existing dowel hole. Use a drill that is 11.5 mm (0.45 inch) in diameter. Drill to a depth of 31.75 mm (1.250 inch).
Illustration 2 g01518729
Use a 2P-5531 Tap in order to tap the recessed hole at the bottom of the hole that was drilled in Step 3. Tap the hole to a thread depth of 8 mm (0.32 inch).
Illustration 3 g01518730
Cross section of pin (1) 9F-2247 Pipe Plug
Install a 9F-2247 Pipe Plug into the recessed hole in order to separate the two grease passages inside the pin.
Illustration 4 g01518734
Use a 2P-5532 Tap in order to tap the hole that was drilled in Step 3. Tap the hole to a thread depth of 12 mm (0.5 inch).
Illustration 5 g01518738
Install a 3B-8490 Grease Fitting into the hole in the top of the pin. Reinstall the 3B-8486 Grease Fitting into the bottom of the pin assembly.
Reinstall the 290-8156 Pin As in the swing frame. Refer to Disassembly and Assembly, RENR6485, "Swing Frame - Install". Install shims, spacers, and washers in order to achieve the proper tolerances for the pin assembly. Refer to the following steps.
Illustration 6 g01520256
Location of pin assembly
Illustration 7 g01520258
(2) 176-0626 Washer (3) 9R-8291 Spacer
Use 176-0626 Washers and 9R-8291 Spacers in order to obtain a maximum gap of 1.0 mm (0.04 inch).
Illustration 8 g01520262
(4) 136-7440 Shim
Illustration 9 g01520339
(A) 0.0 + 1.5 − 1.0 mm (0.00 + 0.06 − 0.04 inch) (B) 0.5 mm (0.02 inch) minimum
Use 136-7440 Shims in order to achieve the tolerances between the pin and the surface of the casting. The tolerances are specified in Illustration 9.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts wiring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.