6D6196 WORM Caterpillar parts
14E
Rating:
Alternative (cross code) number:
CA6D6196
6D-6196
6D6196
CA6D6196
6D-6196
6D6196
Weight: 8 pounds 3 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
31 Dec 2018
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
Caterpillar Worm 6D6196 New
31 Dec 2018
802 Hundredths Pounds
CTP: CTP
Caterpillar WORM (6D6196)
6D6196 Caterpillar Weight(lbs): 8.00 Length(cm): 35.0000 Width(cm): 11.0000 Depth(cm): 11.0000
6D6196 Caterpillar Weight(lbs): 8.00 Length(cm): 35.0000 Width(cm): 11.0000 Depth(cm): 11.0000
07 Oct 2017
CTP: CTP
6D6196 Worm Fits Caterpillar
Warranty
Warranty
This part in 2 request:
Show.
This information for suppliers only!
2017-11-01
2017-10-13
Number on catalog scheme:
24
For full view, you need register
Compatible equipment models: 6D6196:
Information:
Removal Procedure
Illustration 1 g02917036
Illustration 2 g02915178
Slide the locking tab into the unlocked position and disconnect harness assembly (3) from exhaust back pressure sensor (5).
Using a deep socket in order to remove exhaust back pressure sensor (5) from adaptor bracket (7).
Remove O-ring (6) (not shown) from exhaust back pressure sensor (5).
If necessary, follow Step 4.a through Step 4.j in order to remove tube assembly (6).
If necessary, remove the diesel particulate mounting bracket. Refer to Disassembly and Assembly, "Support and Mounting (CEM) - Remove and Install" for the correct procedure.
If necessary, remove the exhaust gas recirculation cooler. Refer to Disassembly and Assembly, "Exhaust Cooler (NRS) - Remove and Install" for the correct procedure.
If necessary, remove the exhaust gas temperature sensor. Refer to Disassembly and Assembly, "Temperature Sensor (Exhaust) - Remove and Install" for the correct procedure.
Disconnect harness assembly (4) from the retaining clip.
Loosen nut (8) and disconnect tube assembly (9).
Remove bolt (2) and remove adaptor bracket (7) from the induction manifold.
Remove banjo bolt (10) from tube assembly (9).
Remove bolt (1) from the bracket for tube assembly (9).
Remove tube assembly (9) from the exhaust manifold.
Remove and sealing washers (11) (not shown). Installation Procedure
Check all components for wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 3 g02915178
Illustration 4 g02917036
If necessary, follow Step 2.a through Step 2.i in order to install tube assembly (6).
Install a new sealing washer (11) (not shown) to banjo bolt (10).
Install banjo bolt assembly (10) into tube assembly (9). Install the remaining new sealing washer (11) (not shown) to banjo bolt assembly (10).
Install tube assembly (9) onto the exhaust manifold and exhaust back pressure sensor bracket (7). Tighten banjo bolt assembly (10) finger tight.
Install bolt (1) to the bracket for tube assembly (6).
Position adaptor bracket (7) onto the induction manifold and install bolt (2).
Tighten nut (8) finger tight.
Tighten bolt (1) and bolt (2) to a torque of 25 N m (221 lb in).
Tighten banjo bolt (10) to a torque of 15 N m (133 lb in).
Tighten nut (8) to a torque of 15 N m (133 lb in).
Install new O-ring seal (6) (not shown) to exhaust back pressure sensor (5).
Install exhaust back pressure sensor (5). Tighten the sensor to a torque of 15 N m (133 lb in)
Connect harness assembly (3) to exhaust back pressure sensor (5) and slide the locking tab into the locked position.
If necessary, install the exhaust gas temperature sensor. Refer to Disassembly and Assembly, "Temperature Sensor (Exhaust) - Remove and Install" for the correct procedure.
If necessary, install the exhaust gas recirculation cooler. Refer to Disassembly and Assembly, "Exhaust Cooler (NRS) - Remove and Install" for the correct procedure.
If necessary, install the diesel particulate mounting bracket. Refer to Disassembly and Assembly, "Support and Mounting (CEM) - Remove and Install" for the correct procedure.
Install harness assembly (4) onto exhaust back pressure sensor bracket (7).
Install bolt (2) to exhaust back pressure sensor (4). Tighten the bolt to a torque of 25 N m (221 lb in).
Illustration 1 g02917036
Illustration 2 g02915178
Slide the locking tab into the unlocked position and disconnect harness assembly (3) from exhaust back pressure sensor (5).
Using a deep socket in order to remove exhaust back pressure sensor (5) from adaptor bracket (7).
Remove O-ring (6) (not shown) from exhaust back pressure sensor (5).
If necessary, follow Step 4.a through Step 4.j in order to remove tube assembly (6).
If necessary, remove the diesel particulate mounting bracket. Refer to Disassembly and Assembly, "Support and Mounting (CEM) - Remove and Install" for the correct procedure.
If necessary, remove the exhaust gas recirculation cooler. Refer to Disassembly and Assembly, "Exhaust Cooler (NRS) - Remove and Install" for the correct procedure.
If necessary, remove the exhaust gas temperature sensor. Refer to Disassembly and Assembly, "Temperature Sensor (Exhaust) - Remove and Install" for the correct procedure.
Disconnect harness assembly (4) from the retaining clip.
Loosen nut (8) and disconnect tube assembly (9).
Remove bolt (2) and remove adaptor bracket (7) from the induction manifold.
Remove banjo bolt (10) from tube assembly (9).
Remove bolt (1) from the bracket for tube assembly (9).
Remove tube assembly (9) from the exhaust manifold.
Remove and sealing washers (11) (not shown). Installation Procedure
Check all components for wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 3 g02915178
Illustration 4 g02917036
If necessary, follow Step 2.a through Step 2.i in order to install tube assembly (6).
Install a new sealing washer (11) (not shown) to banjo bolt (10).
Install banjo bolt assembly (10) into tube assembly (9). Install the remaining new sealing washer (11) (not shown) to banjo bolt assembly (10).
Install tube assembly (9) onto the exhaust manifold and exhaust back pressure sensor bracket (7). Tighten banjo bolt assembly (10) finger tight.
Install bolt (1) to the bracket for tube assembly (6).
Position adaptor bracket (7) onto the induction manifold and install bolt (2).
Tighten nut (8) finger tight.
Tighten bolt (1) and bolt (2) to a torque of 25 N m (221 lb in).
Tighten banjo bolt (10) to a torque of 15 N m (133 lb in).
Tighten nut (8) to a torque of 15 N m (133 lb in).
Install new O-ring seal (6) (not shown) to exhaust back pressure sensor (5).
Install exhaust back pressure sensor (5). Tighten the sensor to a torque of 15 N m (133 lb in)
Connect harness assembly (3) to exhaust back pressure sensor (5) and slide the locking tab into the locked position.
If necessary, install the exhaust gas temperature sensor. Refer to Disassembly and Assembly, "Temperature Sensor (Exhaust) - Remove and Install" for the correct procedure.
If necessary, install the exhaust gas recirculation cooler. Refer to Disassembly and Assembly, "Exhaust Cooler (NRS) - Remove and Install" for the correct procedure.
If necessary, install the diesel particulate mounting bracket. Refer to Disassembly and Assembly, "Support and Mounting (CEM) - Remove and Install" for the correct procedure.
Install harness assembly (4) onto exhaust back pressure sensor bracket (7).
Install bolt (2) to exhaust back pressure sensor (4). Tighten the bolt to a torque of 25 N m (221 lb in).
Caterpillar parts catalog:
Parts worm Caterpillar catalog:
120B, 12F, 140, 140B, 14E
120, 120B, 12E, 140, 140B, 14E
6D3872
WORM
12F, 12G, 14E, 16, 16G
12F, 12G, 14E, 16, 16G
12F, 140, 14E
5D1928
WORM
16
16
6D4542
WORM
16
16
120
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B, 14E
12E
120
12F, 140, 14E
5D8463
WORM
16
16
4D8041
WORM
16
16
6D3872
WORM
12F, 12G, 14E, 16, 16G
12F, 12G, 14E, 16, 16G