5F8353 WRENCH-PRECOMB Caterpillar parts
Rating:
Alternative (cross code) number:
CA5F8353
5F-8353
5F8353
CA5F8353
5F-8353
5F8353
Weight: 0.53 pounds 0 kg.
Compare Prices:
As an associate, we earn commssions on qualifying purchases through the links below
RHOKNSVTL Replacement for fits Pre-Combustion Chamber Wrench Tool Fits Caterpillar Replaces 5F-8353
RHOKNSVTL
RHOKNSVTL
RHOKNSVTL Replacement for fits 5F8353 Pre-combustion Chamber Wrench Fits Caterpillar spline chambers (5F-8353)
RHOKNSVTL
RHOKNSVTL
Reliable Aftermarket Parts Pre-Combustion Chamber Wrench Tool Fits Caterpillar Replaces 5F-8353
Reliable Aftermarket Parts OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
Reliable Aftermarket Parts OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g06259599
Position crankshaft gear (14) and install 12 bolts (13).
Illustration 2 g06259595
Position gear shaft (12) and install four bolts (11).
Tighten four bolts (11) to a torque of 140 10 N m (105 5 lb ft).
Illustration 3 g06259579
Illustration 4 g01068502
(4) Camshaft Idler Gear. (9) Bearing. (E) 81.060 0.010 mm (3.1913 0.0004 inch). (F) 1.00 0.25 mm (0.040 0.010 inch).
Use Tooling (A) and a suitable press to install the bearings in camshaft idler gears (4). Install bearing (9) into gear (4) to Depth (F), as shown.
Place clean engine oil on the bearings and install idler shafts (9).
Machine the inside diameter of bearing (9) to Dimension (E), as shown.Note: The surface finish of Bore (E) must be 0.8 micrometers. Pitch Diameter (H) must be concentric with a total indicator reading of 0.12 mm (0.005 inch). Surface (G) of gear (4) must be square with Bore (E) within 0.05 mm (0.002 inch).
Illustration 5 g06259503
Place clean engine oil on the thrust washer (8) and install.
Illustration 6 g06259470
Position gears (6) into place and install six bolts (5).Tighten six bolts (5) to a torque of 240 20 N m (177 14.8 lb ft).
Illustration 7 g01068516
(2) Cluster Idler Gear. (3) Bearing. (A) 75.060 0.010 mm (2.9551 0.0004 inch). (B) 1.5 0.5 mm (0.06 0.02 inch).
Illustration 8 g06259459
Use Tooling (A) and a suitable press to install bearing (4) in gear (3). Install bearing (4) to Depth (B), as shown.
Replace the gear assembly.
Illustration 9 g06259447Note: When you install the rear cluster gear assembly to the crank gear, there are no timing marks on the G3516 engines.
Put clean engine oil on the bearing and install the gear assembly on the shaft. Make sure that the marks on the gear assembly and the crankshaft are in alignment with the rotation of the engine, as shown.
Place clean engine oil on gear (3) and install gear (3) onto shaft (12).
Install plate (2) and four bolts (1).End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Install".
Install the crankshaft rear seal and wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Rear Seal and Wear Sleeve - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g06259599
Position crankshaft gear (14) and install 12 bolts (13).
Illustration 2 g06259595
Position gear shaft (12) and install four bolts (11).
Tighten four bolts (11) to a torque of 140 10 N m (105 5 lb ft).
Illustration 3 g06259579
Illustration 4 g01068502
(4) Camshaft Idler Gear. (9) Bearing. (E) 81.060 0.010 mm (3.1913 0.0004 inch). (F) 1.00 0.25 mm (0.040 0.010 inch).
Use Tooling (A) and a suitable press to install the bearings in camshaft idler gears (4). Install bearing (9) into gear (4) to Depth (F), as shown.
Place clean engine oil on the bearings and install idler shafts (9).
Machine the inside diameter of bearing (9) to Dimension (E), as shown.Note: The surface finish of Bore (E) must be 0.8 micrometers. Pitch Diameter (H) must be concentric with a total indicator reading of 0.12 mm (0.005 inch). Surface (G) of gear (4) must be square with Bore (E) within 0.05 mm (0.002 inch).
Illustration 5 g06259503
Place clean engine oil on the thrust washer (8) and install.
Illustration 6 g06259470
Position gears (6) into place and install six bolts (5).Tighten six bolts (5) to a torque of 240 20 N m (177 14.8 lb ft).
Illustration 7 g01068516
(2) Cluster Idler Gear. (3) Bearing. (A) 75.060 0.010 mm (2.9551 0.0004 inch). (B) 1.5 0.5 mm (0.06 0.02 inch).
Illustration 8 g06259459
Use Tooling (A) and a suitable press to install bearing (4) in gear (3). Install bearing (4) to Depth (B), as shown.
Replace the gear assembly.
Illustration 9 g06259447Note: When you install the rear cluster gear assembly to the crank gear, there are no timing marks on the G3516 engines.
Put clean engine oil on the bearing and install the gear assembly on the shaft. Make sure that the marks on the gear assembly and the crankshaft are in alignment with the rotation of the engine, as shown.
Place clean engine oil on gear (3) and install gear (3) onto shaft (12).
Install plate (2) and four bolts (1).End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Install".
Install the crankshaft rear seal and wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Rear Seal and Wear Sleeve - Install".
Parts wrench Caterpillar catalog:
5F7839
WRENCH
Caterpillar
Caterpillar
5F7838
WRENCH
Caterpillar
Caterpillar
5F7218
WRENCH
Caterpillar
Caterpillar
5F7213
WRENCH
Caterpillar
Caterpillar
5F7212
WRENCH
Caterpillar
Caterpillar
5F7211
WRENCH-BOX
Caterpillar
Caterpillar
5H9977
WRENCH 7F4581
Caterpillar
Caterpillar
5H5053
WRENCH
Caterpillar
Caterpillar
Caterpillar
5F9322
WRENCH-SOCKET
Caterpillar
Caterpillar
5F9208
WRENCH
Caterpillar
Caterpillar
5F9146
WRENCH
Caterpillar
Caterpillar