1376382 ENGINE AR-PART 2 OF 2 Emission Control Part of 1347000 Engine Ar listed on Page 11.01 An Attachment 315-A

Part No	Qty	Parts name
106-8262	[1]	COOLER GP-ENGINE OIL
116-6725	[1]	LINES GP-WATER
116-6724	[1]	PUMP GP-WATER
106-8270	[1]	MANIFOLD GP-EXHAUST
106-8266	[1]	MANIFOLD GP-INLET
116-6709	[1]	TURBOCHARGER GP
116-6727	[1]	FILTER GP-FUEL
116-6726	[1]	LINES GP-FUEL FILTER
128-3294	[1]	LINES GP-FUEL INJECTION
137-6385	[1]	PUMP GP-FUEL INJECTION
116-6730	[1]	ALTERNATOR GP-CHARGING
116-6728	[1]	PLUG GP-GLOW
141-7818	[1]	STARTING MOTOR GP-ELECTRIC
		GASKET KITS AVAILABLE:
107-3732	[1]	KIT-BOTTOM GASKET
107-3731	[1]	KIT-TOP GASKET

#XEBP72240011

107-3675: CYLINDER BLOCK AS

CYLINDER BLOCK AS

1073675 CYLINDER BLOCK AS
Part of 1068230 Cylinder Block listed on Page 16

c614571 XEBP7224

For full view, you need register

Parts for your 315-A EXCAVATOR:

Pos.	Part No	Qty	Parts name
1.	4D-3118	[3]	PLUG-PIPE
2.	5M-6213	[1]	PLUG
3.	9F-2247	[8]	PLUG
4.	101-6680	[1]	GASKET
5.	103-2229	[6]	PIN-SPRING
6.	095-2005	[1]	CAP
7.	096-3741	[8]	CAP
8.	5I-8009	[1]	BUSHING
9.	5I-7528	[2]	BUSHING
10.	5I-7529	[1]	BUSHING
11.	103-7698	[15]	PLUG
12.	103-9062	[1]	BUSHING
13.	103-9275	[2]	DOWEL
14.	103-9276	[14]	BOLT-BEARING CAP
15.	103-9703	[1]	SHAFT-IDLER
16.	104-1218	[2]	DOWEL
17.	5I-7525	[1]	PLUG
18.	107-3667	[1]	PLUG
19.	107-3669	[6]	JET
20.	107-3672	[1]	VALVE AS-RELIEF
21.	099-4420	[2]	PIN
22.	5I-4993	[1]	SEAL

#XEBP72240012

106-8230: CYLINDER BLOCK GP

CYLINDER BLOCK GP

1068230 CYLINDER BLOCK GP
1053675-Page 14

c614599 XEBP7224

For full view, you need register

Parts for your 315-A EXCAVATOR:

Pos.	Part No	Qty	Parts name
1.	107-3675 Y	[1]	BLOCK AS
2.	103-9279	[2]	SEAL-SIDE

			THE FOLLOWING REPAIR
			KIT IS AVAILABLE:

	128-3811	[1]	KIT-JACKET WATER HEATER
			(INCL CORD AS-HEATER,
			ELEMENT-HEATER, &
			RECEPTACLE-COVERED)
	Y		SEPARATE ILLUSTRATION

#XEBP72240013

116-9988: CRANKSHAFT GP

CRANKSHAFT GP

1169988 CRANKSHAFT GP

c582083 XEBP7224

For full view, you need register

Parts for your 315-A EXCAVATOR:

Pos.	Part No	Qty	Parts name
1.	107-0991	[1]	BEARING SET-MAIN (STANDARD)
	114-5609	[1]	BEARING SET-MAIN (.25MM US)
	114-5610	[1]	BEARING SET-MAIN (.50MM US)
	114-5611	[1]	BEARING SET-MAIN (.75MM US)
2.	117-2830	[1]	CRANKSHAFT AS
3.	103-2235	[1]	KEY-WOODRUFF
4.	117-2829	[1]	GEAR
5.	104-1219	[1]	DOWEL
6.	103-9288	[3]	PLATE-THRUST (STANDARD)
	103-9289	[3]	PLATE-THRUST
	103-9290	[3]	PLATE-THRUST

#XEBP72240014

116-6718: HOUSING GP-FLYWHEEL

HOUSING GP-FLYWHEEL

1166718 HOUSING GP-FLYWHEEL

c582119 XEBP7224

For full view, you need register

Parts for your 315-A EXCAVATOR:

Pos.	Part No	Qty	Parts name
1.	103-9280	[1]	GASKET-REAR
2.	101-6492	[10]	BOLT (25mm LONG)
3.	117-5016	[1]	HOUSING-FLYWHEEL
4.	117-5015	[1]	SEAL AS-OIL
5.	094-2524	[2]	STUD
6.	104-1199	[2]	BOLT (30mm LONG)

#XEBP72240015

116-6715: FLYWHEEL GP

FLYWHEEL GP

1166715 FLYWHEEL GP

c582123 XEBP7224

For full view, you need register

Parts for your 315-A EXCAVATOR:

Pos.	Part No	Qty	Parts name
1.	103-2146	[6]	BOLT
2.	5P-8245	[6]	WASHER
3.	117-4025	[1]	FLYWHEEL AS
4.	117-4026	[1]	GEAR

#XEBP72240016

106-8232: PISTON & ROD GP

PISTON & ROD GP

1068232 PISTON & ROD GP
Part of 1171896 Engine Ar listed on Page 12

c560012 XEBP7224

For full view, you need register

Parts for your 315-A EXCAVATOR:

Pos.	Part No	Qty	Parts name
1.	103-2857	[6]	RING SET-PISTON
	103-2858	[6]	RING SET-PISTON (.25 MM O/S)
	103-2859	[6]	RING SET-PISTON (.50 MM O/S)
2.	103-9679	[6]	PIN-PISTON
3.	103-9680	[6]	ROD AS-CONNECTING
4.	103-9683	[12]	BEARING-CONNECTING ROD
	103-9684	[12]	BEARING-CONNECTING ROD (.25 MM U/S)
	103-9685	[12]	BEARING-CONNECTING ROD (.50 MM U/S)
	103-9686	[12]	BEARING-CONNECTING ROD (.75 MM U/S)
5.	104-1236	[12]	RING-SNAP
6.	107-0984	[6]	PISTON
	107-8255	[6]	PISTON (.25 MM O/S)
	107-8256	[6]	PISTON (.50 MM O/S)

#XEBP72240017

128-3296: PISTON & ROD GP

PISTON & ROD GP

1283296 PISTON & ROD GP
Part of 1376382 Engine Ar listed on Page 13.04
An Attachment

c717874 XEBP7224

For full view, you need register

Parts for your 315-A EXCAVATOR:

Pos.	Part No	Qty	Parts name
1.	103-2857	[6]	RING SET-PISTON
2.	103-9679	[6]	PIN-PISTON
3.	103-9680	[6]	ROD AS-CONNECTING
4.	103-9683	[12]	BEARING-CONNECTING ROD
	103-9684	[12]	BEARING-CONNECTING ROD
	103-9685	[12]	BEARING-CONNECTING ROD
	103-9686	[12]	BEARING-CONNECTING ROD
5.	104-1236	[12]	RING-SNAP
6.	128-3295	[6]	PISTON
7.	122-7311	[6]	SLEEVE-PISTON

#XEBP72240018

116-9987: CAMSHAFT GP

CAMSHAFT GP

1169987 CAMSHAFT GP
An Attachment

c679594 XEBP7224

For full view, you need register

Parts for your 315-A EXCAVATOR:

Pos.	Part No	Qty	Parts name
1.	6V-5215 M	[2]	BOLT (16mm LONG)
2.	9M-1974	[2]	WASHER-HARD
3.	107-8369	[1]	CAMSHAFT AS
4.	094-4628	[1]	KEY
5.	122-9352	[1]	PLATE-THRUST
6.	117-2827	[1]	GEAR
	M		METRIC PART

#XEBP72240019

106-8249: CYLINDER HEAD GP

CYLINDER HEAD GP

1068249 CYLINDER HEAD GP

c605298 XEBP7224

For full view, you need register

Parts for your 315-A EXCAVATOR:

Pos.	Part No	Qty	Parts name
1.	103-9246	[25]	BOLT-CYLINDER HEAD
2.	107-0979	[1]	GASKET-CYLINDER HEAD
3.	107-0978	[1]	CYLINDER HEAD AS
4.	096-9435	[2]	PLUG
5.	103-2782	[12]	SPRING
6.	5I-7625	[12]	RETAINER
7.	1S-0379	[2]	GASKET
8.	5I-7630	[12]	CAP
9.	5I-7719	[24]	COTTER
10.	103-9010	[12]	CAP-SEALING
11.	103-9011	[11]	CAP-SEALING
12.	103-9247	[12]	GUIDE-VALVE
13.	103-9252	[6]	SEAT-VALVE
14.	103-9253	[6]	SEAT-VALVE
15.	103-9260	[12]	SEAL-VALVE STEM
16.	103-9269	[6]	VALVE-INLET
17.	103-9270	[6]	VALVE-EXHAUST

Information:

ENGINE ARRANGEMENT

ENGINE AR

Truck Engine News

Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
2015/09/18

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed in Truck Engine News {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed in Truck Engine News {0374, 1000, 7000}

Engine News

Improved Registration Process for Retrofit Products {1000, 7000}
2011/04/15

Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
2015/09/25

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed in Engine News {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed in Engine News {0374, 1000, 7000}

Procedure for Cleaning an Engine Lubrication System when Contaminated with Engine Coolant Containing Antifreeze {1000, 1348, 1395}
Procedure for Cleaning an Engine Lubrication System when Contaminated with Engine Coolant Containing Antifreeze {1000, 1348, 1395}

Special Instruction

Caterpillar DPF Installation and Operation Guide for Diesel Engines - California Only {1000, 1091}
Caterpillar DPF Installation and Operation Guide for Diesel Engines - California Only {1000, 1091}

Generation 3 DPFdm Diagnostic Module Installation Manual - California Only {1000, 1091, 7490}
Generation 3 DPFdm Diagnostic Module Installation Manual - California Only {1000, 1091, 7490}

Storage Procedure for Caterpillar Products {0355, 1000, 7000}
Storage Procedure for Caterpillar Products {0355, 1000, 7000}

Recommended Storage Procedures For Hydraulic Excavators {0355, 1000, 1250, 7000}
Recommended Storage Procedures For Hydraulic Excavators {0355, 1000, 1250, 7000}

Instructions to Register the Retrofit and Submit Service Reporting {1000, 3000, 7000, 7570}
Instructions to Register the Retrofit and Submit Service Reporting {1000, 3000, 7000, 7570}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}

Differences in Appearance of Cat <SUP>®</SUP> Reman Parts when Compared to New Parts {1000, 1250}
Differences in Appearance of Cat ^® Reman Parts when Compared to New Parts {1000, 1250}

Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}
Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}

Technical Information Bulletin

A Recommendation for Initial Parts Stock Quantities Will Now Be Included in Service Letters{1000, 7000, 7751, 7752}
A Recommendation for Initial Parts Stock Quantities Will Now Be Included in Service Letters{1000, 7000, 7751, 7752}

Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}

368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620}
368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620}

Specifications

Engine Design
3046 Engine for Caterpillar Built Machines

Tool Operating Manual

Using the 1U-8860 Large Engine Blowby Pickup Group and the 8T-2700 Blowby/Airflow Indicator{0781, 0785, 1000}
Using the 1U-8860 Large Engine Blowby Pickup Group and the 8T-2700 Blowby/Airflow Indicator{0781, 0785, 1000}

NEHS1111: 368-9910 Multi-Tool Group 3 {0599, 0701, 0702, 0706, 1000, 7610, 7620}
NEHS1111: 368-9910 Multi-Tool Group 3 {0599, 0701, 0702, 0706, 1000, 7610, 7620}

142-6893 Adjustable Lifting Bracket Group{0599, 0629, 0632, 0701, 0717, 1000, 4000, 7000}
142-6893 Adjustable Lifting Bracket Group{0599, 0629, 0632, 0701, 0717, 1000, 4000, 7000}

Reuse And Salvage Guidelines

Reuse and Testing of Fuel Injection Pump Housing {0374, 1000, 1250, 1300}
Reuse and Testing of Fuel Injection Pump Housing {0374, 1000, 1250, 1300}

HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562}
HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562}

Cleaning Components with Carbon Dioxide (CO<SUB>2</SUB>) {0680, 1000, 7000}
Cleaning Components with Carbon Dioxide (CO₂) {0680, 1000, 7000}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}

Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}
Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}

Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}
Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}

Contamination Control Guidelines

Proper Oil Changing Procedures {1000, 1308, 1316, 1325, 1348, 3000, 3004, 3005, 3030, 3064, 3067, 3080, 3081, 4000, 4001, 4050, 4051, 5050, 5056, 5068, 5095}
Proper Oil Changing Procedures {1000, 1308, 1316, 1325, 1348, 3000, 3004, 3005, 3030, 3064, 3067, 3080, 3081, 4000, 4001, 4050, 4051, 5050, 5056, 5068, 5095}

Information Release Memo

REMAN ENGINES DESIGNATED AND LABELED AS REPLACEMENT ENGINES
REMAN ENGINES DESIGNATED AND LABELED AS REPLACEMENT ENGINES

DISCONTINUATION OF REMAN 3044 / 3046 / 3064 / 3066 MHI ENGINES
DISCONTINUATION OF REMAN 3044 / 3046 / 3064 / 3066 MHI ENGINES

Testing and Adjusting

Engine Speed - Check
3046 Engine for Caterpillar Built Machines

Troubleshooting
3046 Engine for Caterpillar Built Machines

Technical Analysis

Technical Analysis 1 (TA1) Visual Inspection for Excavator {0372, 1000, 7000, 753T, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Excavator {0372, 1000, 7000, 753T, 7565}

Disassembly and Assembly

Engine & Main Hydraulic Pump
SUPPLEMENT FOR - 3046 ENGINE 315 & 315 L EXCAVATORS

Service Magazine

Solenoid Valve Assembly Is Improved In Pilot Lines Group {5479,5057}
1999/03/29

A New Screen In The TMI System Provides The Status Of Emission Certification Of Engines {1000}
2001/01/08

Caterpillar's Position On The Use Of Biodiesel Fuel In Caterpillar Engines {1000}
2012/08/28

A List Of Contacts For Caterpillar Product Support Is Available {1000, 4450, 7000}
2002/03/25

Proper Long Term Storage of Caterpillar Products {0355, 1000, 7000}
2009/04/27

Changes To Caterpillar Incident Reporting Field Use Form And DSN Incident Report Entry Screens {1000, 7000}
2009/11/18

Redesigned Fluid Sampling Valves Are Now Available for All Cat Products {7542}
2011/02/11

Improved Registration Process for Retrofit Products {1000, 3000, 7000, 7570}
2011/02/17

TA2 (Technical Analysis) Inspections are Now Available on SIS {0372, 1000, 7000, 753T, 7565}
2013/01/10

Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
2015/09/25

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}
Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}

Process to Print Collage Schematics {0374, 1000, 7000}
Process to Print Collage Schematics {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed on Service Magazines {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed on Service Magazines {0374, 1000, 7000}

A New Process Is Available to Request Service Animations for Certain Service Information Procedures {1000, 7000}
A New Process Is Available to Request Service Animations for Certain Service Information Procedures {1000, 7000}

Caterpillar Parts SIS Catalog 315-A :

102-3841 INSTALLATION AR-ENGINE

107-3675 CYLINDER BLOCK AS

106-8230 CYLINDER BLOCK GP

116-9988 CRANKSHAFT GP

116-6718 HOUSING GP-FLYWHEEL

116-6715 FLYWHEEL GP

106-8232 PISTON & ROD GP

128-3296 PISTON & ROD GP

116-9987 CAMSHAFT GP

1376382 ENGINE AR-PART 2 OF 2 Emission Control Part of 1347000 Engine Ar listed on Page 11.01 An Attachment 315-A

ENGINE ARRANGEMENT