941B TRACK TYPE TRACTOR / POWERSHIFT / 16U00226-UP (MACHINE) POWERED BY 3304 ENGINE IMPLEMENTS Caterpillar SIS




TRACK LOADER 941 TRACK LOADER 16U
 941B TRACK TYPE TRACTOR / POWERSHIFT / 16U00226-UP (MACHINE) POWERED BY 3304 ENGINE XMBP9543 941 16U   (1971)

Parts group 941:

  For full view, you need register
IMPLEMENTS
CONTROL GP
BUCKET POSITIONER
8K-8777 BUCKET POSITIONER
BUCKET POSITIONER (8K8777 N/S)
Effective with Serial No. 16U226~16U395
8J82 Valve Group parts are shown on Page 330
BUCKET POSITIONER
8K-8777 BUCKET POSITIONER
BUCKET POSITIONER (8K8777 N/S)
Effective with Serial No. 16U396-UP
8J82 Valve Group parts are shown on Page 330
KICKOUT
6K-4394 KICKOUT
KICKOUT (6K4394 N/S)
Effective with Serial No. 16U226-Up
LINKAGE GP
CONTROL GP-BUCKET
7K-9641 CONTROL GP-BUCKET
BUCKET CONTROL (7K9641 N/S)
Effective with Serial No. 16U226~16U240
CONTROL GP-BUCKET
7K-9641 CONTROL GP-BUCKET
BUCKET CONTROL (7K9641 N/S)
Effective with Serial No. 16U241-UP

Information:

(For parts list, see above)

Special Instruction
Decommissioning Procedure for Permanently Sealed Diaphragm Accumulators {5077}
Decommissioning Procedure for Permanently Sealed Diaphragm Accumulators {5077}
Service Magazine
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1981/02/23
Special Instruction
Installation of 9C1916 Louver{5258, 7304}
Installation of 9C1916 Louver{5258, 7304}
Repair of Track Loader Lift Arms And Levers {6107}
Repair of Track Loader Lift Arms And Levers {6107}
Service Magazine
Worn Tilt Lever Bores{6116,6126,6127}
1981/08/24
Washers Can Be Used On Linkage Pins{6108}
1977/04/18
Revised Special Instruction, SEHS8433-04, "Repair Of Wheel And Track Loader Lift Arms And Levers" Available {0374,6107,6116,6119}
1998/12/07
New Crankshaft Assemblies{1202,1204,1206,1207,1212}
1982/11/01
Exhaust Dust Ejector Operation{1055,1068}
1994/09/26
Special Instruction
Installation Of Lift Arm And Bearing Assemblies{6119}
Installation Of Lift Arm And Bearing Assemblies{6119}
Service Magazine
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
New Crankshaft Assemblies{1202,1204,1206,1207,1212}
1982/11/01
Special Instruction
Installation Of Lift Arm And Bearing Assemblies{6119}
Installation Of Lift Arm And Bearing Assemblies{6119}
Service Magazine
Washers Can Be Used On Linkage Pins{6108}
1977/04/18
Revised Special Instruction, SEHS8433-04, "Repair Of Wheel And Track Loader Lift Arms And Levers" Available {0374,6107,6116,6119}
1998/12/07
Special Instruction
Installation Of Lift Arm And Bearing Assemblies{6119}
Installation Of Lift Arm And Bearing Assemblies{6119}
Service Magazine
Worn Tilt Lever Bores{6116,6126,6127}
1981/08/24
Washers Can Be Used On Linkage Pins{6108}
1977/04/18
Special Instruction
Installation Of Lift Arm And Bearing Assemblies{6119}
Installation Of Lift Arm And Bearing Assemblies{6119}
Service Magazine
New Corner Guard System Improves Bucket Performance And Increases Service Life; Drawings For Fabricated Welding Fixture Available{6120,6121,6122,6801,6802,0626,6101,6103,6104}
1980/10/27
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1981/02/23
Worn Tilt Lever Bores{6116,6126,6127}
1981/08/24
New Bucket Cutting Edges Give Longer Service Life And Improved Penetration (Cutting Ability){6801}
1981/11/16
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
New Crankshaft Assemblies{1202,1204,1206,1207,1212}
1982/11/01
Use the 6V6167 Contact Point to Measure Wear Steps on Piston Pins{0653}
1982/11/22
Bucket End Bits Are Thicker Than Bucket Center Edges{6804}
1983/05/30
Procedure To Install Weld-On Half Arrow Cutting Edges{6800,6801,6805}
1984/10/08
Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08
Washers Can Be Used On Linkage Pins{6108}
1977/04/18
Cartridge Relief Valve Adjustments{5069}
1978/09/04
New Tip Pin Retainer Can Be Too Thick To Fit IN Adapter Counterbore{6803}
1979/09/03
Use the 6V6167 Contact Point to Measure Wear Steps on Piston Pins{0653}
1982/11/22
Washers Can Be Used On Linkage Pins{6108}
1977/04/18
New Color Used For Fan Belt Tightener Spring{1358}
1984/06/04
Welding Fixture For Installation Of Bucket Corner Guards Available{0626,6100,6801,6802}
1981/03/30
Cartridge Relief Valve Adjustments{5069}
1978/09/04
Reuse And Salvage Guidelines
Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 1, 2, and 3) {5061, 5073}
Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 1, 2, and 3) {5061, 5073}
Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 4, 5, and 6) {5061, 5073}
Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 4, 5, and 6) {5061, 5073}
Removing and Installing Bushings and Pressure Plates in Hydraulic Gear Pumps {5073}
Removing and Installing Bushings and Pressure Plates in Hydraulic Gear Pumps {5073}

Truck sale:

Caterpillar 941, Construction
3,000 
Caterpillar 941, Construction
- track loaders
MICHIGAN CAT
7038 - CAT 941
 
7038 - CAT 941

avspare
1974 CAT 941
USD $13,750 
1974 CAT 941

WESTERN MICHIGAN EQUIPMENT
Traverse City, Michigan
1980 CAT 941
Call 
1980 CAT 941

DDG Equipment
1974 CAT 941
USD $5,500 
1974 CAT 941

RP Equipment
Allentown, Pennsylvania