1911830 YOKE Caterpillar parts
950G, 950G II, 950H, 950K, 962G, 962G II
Rating:
Alternative (cross code) number:
CA1911830
191-1830
1911830
CA1911830
191-1830
1911830
Weight: 19 pounds 8 kg.
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$185.59
29 Aug 2022
20.3486[9.16] Pounds
US: TakePart
Caterpillar YOKE-BRAKE (1911830) New Aftermarket By CTP
REPLACEMENT CATERPILLAR
REPLACEMENT CATERPILLAR
Information:
Water in the fuel can cause the engine to run rough. Water in the fuel may cause an electronic unit injector to fail. If the fuel has been contaminated with water, the element should be changed before the regularly scheduled interval. The primary filter/water separator also provides filtration in order to help extend the life of the secondary fuel filter. The element should be changed regularly. If a vacuum gauge is installed, the primary filter/water separator should be changed at 50 to 70 kPa (15 to 20 inches hg).Replace the Element
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over any disconnected fuel system components.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Cat Dealer Service Tool Catalog" or refer to Special Publication, PECJ0003, "Cat Shop Supplies and Tools Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Close the main fuel supply valve.
Illustration 1 g01453091
Typical primary fuel filter/water separator
(1) Primary fuel filter element
(2) Collection bowl for the water separator
(3) Drain for the water separator
Remove the element from the element mounting base while the bowl is attached.
Dispose of the fuel in the fuel filter element. Remove the bowl from the element . The bowl is reusable. Do not discard the bowl. Dispose of the used element.
Remove the O-ring from the bowl. Clean the following components:
Bowl
O-ring
Mounting baseInspect the O-ring for damage and for deterioration. Replace the O-ring, if necessary.
The primary filter/water separator may be prefilled with fuel to avoid rough running/stalling of the engine due to air. Do not fill the secondary filter with fuel before installation. The fuel would not be filtered and could be contaminated. Contaminated fuel will cause accelerated wear to fuel system parts.
Lubricate the O-ring with clean diesel fuel. The element may be filled with fuel at this time.
Install the bowl on a new element. Tighten the bowl by hand. Do not use tools in order to tighten the bowl.
The water separator is under suction during normal engine operation. Ensure that the vent plug is tightened securely to help prevent air from entering the fuel system.
Open the main fuel supply valve.
Start the engine and check for leaks. Run the engine for 1 minute. Stop the engine and check for leaks again. Detection of leaks is difficult while the engine is running. The primary filter/water separator is under suction. A leak will allow air to enter the fuel. The air in the fuel can cause
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over any disconnected fuel system components.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Cat Dealer Service Tool Catalog" or refer to Special Publication, PECJ0003, "Cat Shop Supplies and Tools Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Close the main fuel supply valve.
Illustration 1 g01453091
Typical primary fuel filter/water separator
(1) Primary fuel filter element
(2) Collection bowl for the water separator
(3) Drain for the water separator
Remove the element from the element mounting base while the bowl is attached.
Dispose of the fuel in the fuel filter element. Remove the bowl from the element . The bowl is reusable. Do not discard the bowl. Dispose of the used element.
Remove the O-ring from the bowl. Clean the following components:
Bowl
O-ring
Mounting baseInspect the O-ring for damage and for deterioration. Replace the O-ring, if necessary.
The primary filter/water separator may be prefilled with fuel to avoid rough running/stalling of the engine due to air. Do not fill the secondary filter with fuel before installation. The fuel would not be filtered and could be contaminated. Contaminated fuel will cause accelerated wear to fuel system parts.
Lubricate the O-ring with clean diesel fuel. The element may be filled with fuel at this time.
Install the bowl on a new element. Tighten the bowl by hand. Do not use tools in order to tighten the bowl.
The water separator is under suction during normal engine operation. Ensure that the vent plug is tightened securely to help prevent air from entering the fuel system.
Open the main fuel supply valve.
Start the engine and check for leaks. Run the engine for 1 minute. Stop the engine and check for leaks again. Detection of leaks is difficult while the engine is running. The primary filter/water separator is under suction. A leak will allow air to enter the fuel. The air in the fuel can cause
Cat SIS web machinery list:
Parts yoke Caterpillar catalog:
1120782
YOKE
950 GC, 950G, 950G II, 950H, 950K, 962G, 962G II, 962K, IT62G
950 GC, 950G, 950G II, 950H, 950K, 962G, 962G II, 962K, IT62G
1561151
YOKE AS
950 GC, 950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
950 GC, 950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
1151326
YOKE AS
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
1150531
YOKE
950G, 962G, IT62G
950G, 962G, IT62G
1151653
YOKE
950G, 950G II, 950H, 950K, 962G, 962G II, IT62G
950G, 950G II, 950H, 950K, 962G, 962G II, IT62G
1555602
YOKE
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
1555608
YOKE-BRAKE
950G, 950G II, 962G, 962G II, IT62G, IT62G II
950G, 950G II, 962G, 962G II, IT62G, IT62G II
1555606
YOKE
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966M, 966M XE, 972M, 972M XE, IT62G, IT62G II, IT62H
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966M, 966M XE, 972M, 972M XE, IT62G, IT62G II, IT62H
1911831
YOKE
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G II, IT62H
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G II, IT62H
1552077
YOKE
834G, 834H, 836G, 836H, 988G, 988H
834G, 834H, 836G, 836H, 988G, 988H
1730714
YOKE
834G, 834H, 834K, 836G, 836H, 836K, 986H, 988G, 988H, 988K, AD45B, AD55, AD55B, AD60
834G, 834H, 834K, 836G, 836H, 836K, 986H, 988G, 988H, 988K, AD45B, AD55, AD55B, AD60
1730715
YOKE AS
834G, 834H, 834K, 836G, 836H, 836K, 986H, 988G, 988H, 988K, AD45B, AD55, AD55B, AD60
834G, 834H, 834K, 836G, 836H, 836K, 986H, 988G, 988H, 988K, AD45B, AD55, AD55B, AD60
1488889
YOKE AS
834G, 834H, 836G, 836H, 988G, 988H
834G, 834H, 836G, 836H, 988G, 988H
1174465
YOKE AS
966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE
966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE
8E4615
YOKE AS
834B, 988F II
834B, 988F II
2V5893
YOKE AS
789, 789B, 793, 793B, 992C, 992D, 994
789, 789B, 793, 793B, 992C, 992D, 994
6I8053
YOKE AS
992C, 992D, PM-201, PM-465, PM-565, PM-565B
992C, 992D, PM-201, PM-465, PM-565, PM-565B
7K2793
YOKE AS
992, 992C, 992D
992, 992C, 992D
9C3097
YOKE
992C, 992D
992C, 992D
6M9618
YOKE
992C, 992D
992C, 992D
7K2792
YOKE AS
992, 992C
992, 992C