AVSPARE.COM
parts catalog

YOKE AS-REAR 3967254 - Caterpillar



3967254 YOKE AS-REAR Caterpillar parts CD-54B YOKE
Rating:
23
Alternative (cross code) number:
CA3967254
396-7254
3967254
Caterpillar 3967254 YOKE AS-REAR

Buy YOKE AS-REAR 3967254 Caterpillar genuine, new aftermarket tractor parts with delivery
VIBRATORY COMPACTOR,

Compatible equipment models: 3967254:

VIBRATORY COMPACTOR  CD-54B   Caterpillar
Number on catalog scheme: 2
  
  For full view, you need register
3967254 Images:
Caterpillar parts 3967254

Information:

Specification
Table 1
Swing Speed    
Item    Specification    
305.5E
Right Swing     3.5 sec or less    
Left Swing    
Table 2
Swing Drift (1)    
Bucket Load
(kg)     Time
(min)     Swing Drift
(mm)
(inch)    
210.0     3.0     0    
( 1 ) Maximum DriftIntroduction
Measuring the swing speed on a slope will determine if there is a need to check the swing motor. Measuring the swing drift on a slope will determine if there is a need to check the swing parking brake.Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".Required Tools
Table 3
Required Tools    
Description    Qty    
Tape Measure     1    
Stopwatch     1    Test Procedure
Swing Speed on a Slope
Illustration 1 g03332341
(A) 12 degrees
Complete the following steps in order to measure the swing speed on a slope.
Start the engine.
Place the engine speed dial in the HIGH IDLE position.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Position the machine on a slope of 12 degrees. Refer to Illustration 1.
Position the implements at maximum reach and close the bucket. Position the bucket above the ground so that the bucket will not come in contact with any obstacles.
Illustration 2 g03555942
Position the upper structure at position (X). The upper structure should be at a 90 degree angle to the lower structure. Refer to Illustration 2.
Measure the time that is required to swing the upper structure from position (X) to position (Y) .
Position the upper structure at position (Z). The upper structure should be at a 90 degree angle to the lower structure.
Measure the time that is required to swing the upper structure from position (Z) to position (Y) .Swing Drift on a Slope
Complete the following steps in order to measure the swing drift on a slope.
Illustration 3 g03555942
Load the bucket.Weight of bucket load with 305.5E excavators: ... 210 kg (463 lb)
Position the upper structure at position (X). The upper structure should be at a 90 degree angle to the lower structure. Refer to Illustration 3.
Illustration 4 g00293972
(A) Upper frame (B) Undercarriage frame (C) Marking
To indicate the relationship of the two positions, put a mark (C) on the inner race and the outer race of the swing bearing. Refer to Illustration 4.
Start the engine. Position the implements at maximum reach. Place the engine at the LOW IDLE position. Place the hydraulic activation lever in the UNLOCKED position.
Leave the machine in this position for 3 minutes. Measure the swing drift on the circumference of the swing bearing.
Position the upper structure at position (Z). The upper structure should be at a 90 degree angle to the lower structure. Refer

Caterpillar parts catalog:

Caterpillar parts catalog
CD44B CD54B Vibratory Asphalt Compactor GRT00001-UP (MACHINE) POWERED BY C3.4 Engine
CD44B Asphalt Compactor 39800001-UP (MACHINE) POWERED BY C3.4 Engine


Parts yoke Caterpillar catalog:

3732729 YOKE AS
CP-54B, CS-54B
3732739 YOKE AS
CS-74B, CS-78B
3732738 YOKE AS
CP-74B, CS-74B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.